Engine Oil Filter Base - Install - 3054 Engine
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Install a new gasket for the engine oil filter base (2) .
Show/hide table
Illustration 1 | g00843430 |
- Install the engine oil filter base (2) to the cylinder block.
- Install four bolts (1) that secure the engine oil filter base (2) to the cylinder block.
- Install the cooling lines for the engine oil cooler. Tighten hose clamps (4) .
- Install a new oil filter (3) .
- If equipped, install the engine oil line to the engine oil filter base (2). Tighten the oil filter by hand. Refer to the instructions that are in the Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct installation procedure. Do not overtighten the oil filter.
Caterpillar Information System:
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Remove
2001/12/01 Recommended Setting Of The Oil Mist Detector Alarm Changed {1336}
3126 Truck Engine Military Inlet Manifold - Remove
Electronic Modular Control Panel II (EMCP II) Engine Setpoint Verification OP9
Electronic Modular Control Panel II (EMCP II) Spare Input/Output Programming OP6
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Upper Bearing - Remove and Install
3408E and 3412E Industrial Engines Diagnostic Flash Code Retrieval
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 02 (for EUI Engines)
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Lower Bearing - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Travel Brake Valve - Install
3126 Truck Engine Military Inlet Manifold - Install
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3056 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3056 Engine
Electronic Modular Control Panel II (EMCP II) SP Fault Code
Electronic Modular Control Panel II (EMCP II) Charging System
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Remove
3054 and 3056 Marine Generator Set Engines Engine Oil Cooler - Remove and Install - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Disassemble
3054 and 3056 Marine Generator Set Engines Water Pump - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Assemble
Electronic Modular Control Panel II (EMCP II) Pulse Width Modulated Sensor