Swing Gear and Bearing - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 6V-2157     | Link Bracket     | 4     |
Start By:
- Remove the undercarriage frame.
- Put an alignment mark on the swing gear and bearing and the undercarriage frame for assembly purposes. Remove thirty bolts (2) and the spacers that hold swing gear and bearing (1) to the undercarriage frame.
Show/hide table
Illustration 1 | g00365812 |
Show/hide table
Illustration 2 | g00365813 |
- Fasten Tool (A) and a hoist to the swing gear and bearing, as shown. The bolts and spacers that hold the upper structure to the undercarriage frame can be used to install Tool (A) .
- Remove the swing gear and bearing. The weight of the swing gear and bearing is approximately 227 kg (500 lb).
- Put tape over the sealing surfaces of the dust seals, the inner race and the outer race. The tape will prevent the cleaning solvent from entering the cross section of the dust seals. Thoroughly clean the swing gear and bearing.
Show/hide table
Illustration 3 | g00365832 |
Typical example |
- Remove dust seals (3) and (4) from the outer race and the inner race of the swing gear and bearing.
- Clean the sealing grooves of the inner race and the outer race with a fine grit sandpaper. Use a cleaning solvent to clean the seal grooves. Be sure that the seal grooves are thoroughly clean and dry prior to installing new dust seals.
Caterpillar Information System:
2001/12/01 Recommended Setting Of The Oil Mist Detector Alarm Changed {1336}
3126 Truck Engine Military Inlet Manifold - Remove
Electronic Modular Control Panel II (EMCP II) Engine Setpoint Verification OP9
Electronic Modular Control Panel II (EMCP II) Spare Input/Output Programming OP6
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Upper Bearing - Remove and Install
3408E and 3412E Industrial Engines Diagnostic Flash Code Retrieval
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 02 (for EUI Engines)
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Lower Bearing - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Travel Brake Valve - Install
3054 and 3056 Industrial and Generator Set Engines Engine Oil Cooler - Inspect
Electronic Modular Control Panel II (EMCP II) Indicators of Alarm Module Are Constantly Flashing
SPT343 Truck Mounted Pumper Model View Illustrations
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Install
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3054 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3054 Engine
3126 Truck Engine Military Inlet Manifold - Install
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3056 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3056 Engine
Electronic Modular Control Panel II (EMCP II) SP Fault Code
Electronic Modular Control Panel II (EMCP II) Charging System
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Remove
3054 and 3056 Marine Generator Set Engines Engine Oil Cooler - Remove and Install - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Disassemble