Specifications
发动机一般技术规格
Show/hide table
图 1 | g00845204 |
(1 到 8) 气缸数 (A) 进气门 (B) 排气门 (C) 飞轮 |
Show/hide table
G3508 发动机技术规格     | |
额定转速     | 1000 至 1800     |
气缸及排列     | 65 度 V 型 8     |
缸径     | 170 mm (6.7 in)     |
冲程     | 190 mm (7.5 in)     |
排量     | 34.5 L (2105 立方英寸)     |
压缩比     | 7.5:1     |
8:1 | |
11:1 | |
12.5:1 | |
进气方式     | 自然吸气式     |
涡轮增压后冷式 独立回路后冷 |
|
旋转方向(飞轮端)     | 标准旋向为逆时针方向。     |
顺时针方向为可选旋向。 | |
进气阀间隙     | 0.51 mm (0.020 in)     |
排气阀间隙     | 1.27 mm (0.050 in)     |
Show/hide table
图 2 | g00845207 |
(1 到 12) 气缸数 (A) 进气门 (B) 排气门 (C) 飞轮 |
Show/hide table
G3512 发动机技术规格     | |
额定转速     | 1000 至 1800     |
气缸及排列     | 65 度 V 型 12     |
缸径     | 170 mm (6.7 in)     |
冲程     | 190 mm (7.5 in)     |
排量     | 51.8 L (3158 立方英寸)     |
压缩比     | 7.5:1     |
8:1 | |
11:1 | |
12.5:1 | |
进气方式     | 自然吸气式     |
涡轮增压后冷式 独立回路后冷 |
|
旋转方向(飞轮端)     | 标准旋向为逆时针方向。     |
顺时针方向为可选旋向。 | |
进气阀间隙     | 0.51 mm (0.020 in)     |
排气阀间隙     | 1.27 mm (0.050 in)     |
Show/hide table
图 3 | g00845212 |
(1 到 16) 气缸数 (A) 进气门 (B) 排气门 (C) 飞轮 |
Show/hide table
G3516 发动机技术规格     | |
额定转速     | 1000 至 1800     |
气缸及排列     | 65 度 V 型 16     |
缸径     | 170 mm (6.7 in)     |
冲程     | 190 mm (7.5 in)     |
排量     | 69 L (4210 立方英寸)     |
压缩比     | 7.5:1     |
8:1 | |
11:1 | |
12.5:1 | |
进气方式     | 自然吸气式     |
涡轮增压后冷式 独立回路后冷 |
|
旋转方向(飞轮端)     | 标准旋向为逆时针方向。     |
顺时针方向为可选旋向。 | |
进气阀间隙     | 0.51 mm (0.020 in)     |
排气阀间隙     | 1.27 mm (0.050 in)     |
曲轴的气门间隙设置位置
Show/hide table
曲轴的气门间隙设置位置 标准逆时针旋转     |
|||
发动机     | 第 1 缸处于上死点位置时的冲程 (1)     | 进气门     | 排气门     |
G3508     | 压缩冲程     | 1-2-6-8     | 1-2-3-7     |
排气冲程 | 3-4-5-7     | 4-5-6-8     | |
点火顺序 | 1-2-7-3-4-5-6-8     | ||
G3512     | 压缩冲程     | 1-3-6-7-10-12     | 1-4-5-6-9-12     |
排气冲程 | 2-4-5-8-9-11     | 2-3-7-8-10-11     | |
点火顺序 | 1-12-9-4-5-8-11-2-3-10-7-6     | ||
G3516     | 压缩冲程     | 1-2-5-7-8-12-13-14     | 1-2-3-4-5-6-8-9     |
排气冲程 | 3-4-6-9-10-11-15-16     | 7-10-11-12-13-14-15-16     | |
点火顺序 | 1-2-5-6-3-4-9-10-15-16-11-12-13-14-7-8     | ||
曲轴的气门间隙设置位置 可选的顺时针旋向     |
|||
G3508     | 压缩冲程     | 1-3-4-8     | 1-2-7-8     |
排气冲程 | 2-5-6-7     | 3-4-5-6     | |
点火顺序 | 1-8-7-2-6-5-4-3     | ||
G3512     | 压缩冲程     | 1-3-4-6-7-12     | 1-4-5-8-9-12     |
排气冲程 | 2-5-8-9-10-11     | 2-3-6-7-10-11     | |
点火顺序 | 1-4-9-8-5-2-11-10-3-6-7-12     | ||
G3516     | 压缩冲程     | 1-2-5-6-7-8-13-14     | 1-2-3-4-5-6-9-10     |
排气冲程 | 3-4-9-10-11-12-15-16     | 7-8-11-12-13-14-15-16     | |
点火顺序 | 1-6-5-4-3-10-9-16-15-12-11-14-13-8-7-2     |
Show/hide table
( 1 ) | 有关完整的程序,请参阅维修手册, "系统操作测试和调整"。 |
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) Engine Does Not Shutdown (for EUI Engines)
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Permanent Timing Calibration Sensor
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Injector Solenoids
Power Module Switchgear (Low Voltage and Medium Voltage) Glossary
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Contactor - Remove and Install
Electronic Modular Control Panel II (EMCP II) Starting Motor Remains Engaged (for MUI Engines)
2001/11/19 A New Edition of the Special Publication, SEBD0640, "Oil and Your Engine" is Available {1348}
2001/11/01 A New Edition of the Special Publication, SEBD0640, "Oil and Your Engine" is Available {1348}
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Ether Injection System
2002/02/01 Turbocharger Compressor Bypass Valve is used on 3616 Engines {1081}
3512B Petroleum Engines with the ADEM 2 Electronic Control Module Engine Speed/Timing Sensor
3126 Truck Engine (Military) Air Inlet and Exhaust System - Inspect
Electronic Modular Control Panel II (EMCP II) Engine Does Not Shutdown (for MUI Engines)
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Adjuster - Disassemble
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Adjuster - Assemble
Electronic Modular Control Panel II (EMCP II) GSC Operation Is Erratic
G3500 Engines Plate Locations and Film Locations
Electronic Modular Control Panel II (EMCP II) Display of Voltage or Current Is Zero
Electronic Modular Control Panel II (EMCP II) Display of Voltage or Current is Inaccurate
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Fuse - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Final Drive Sprocket - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Travel Brake Valve - Remove
SPT343 Truck Mounted Pumper Model View Illustrations
Electronic Modular Control Panel II (EMCP II) Indicators of Alarm Module Are Constantly Flashing