914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Caterpillar


MID 079 - CID 0346 - FMI 03

Usage:

IT14G 1WN
产生此代码的情况:

当 ECM 检测到对蓄电池正极电压短路时,指示该故障。 短路发生在 ECM 到继电器线圈的通路中。 如果存在该故障,无论行驶速度如何,行驶控制系统都会被激活。 无论开关位置如何,行驶控制系统都会被激活。

系统响应:

在出现该诊断代码时,监视器上显示警告。

测试步骤 1. 检查继电器。

  1. 把钥匙开关转到断开位置。

  1. 将行驶控制装置继电器从插座上拆下。

  1. 将起动开关转到接通位置。

  1. 测量端子 85 与端子 86 之间的电压。

注: 该步骤导致控制装置记录该继电器的开路代码。 故障排除后清除该代码。

预期结果:

电压约为蓄电池电压。

结果:

  • 是 - 继电器故障。 更换继电器。

  • 否 - 电压约为蓄电池电压。 转至测试步骤 2。

测试步骤 2. 检查线束

  1. 把钥匙开关转到断开位置。

  1. 从控制装置上断开机器线束。

  1. 把钥匙开关转到接通位置。

  1. 定位控制装置线束接头。 测量触点 2 和触点 37 之间的电压。

预期结果:

电压约为 0 VDC。

结果:

  • 是 - 电压约为蓄电池电压。 机器线束中存在对蓄电池正极电压的短路。

    修复: 修理或更换线束。

    停止

  • 否 - 电压约为 0 DCV。 未找到故障原因。 转至测试步骤 3。

测试步骤 3. 该故障仍然激活。

  1. 将起动开关转到断开位置。

  1. 检查并重新连接接头。

  1. 安装继电器。

  1. 将起动开关转到接通位置。

  1. 进入维修模式。

  1. 操作机器。

  1. 该故障仍然激活。

结果:

  • 是 - 该故障没有排除。 控制装置不太可能故障。 再次执行以上步骤。 如果没有找到故障原因,则更换控制装置。

    修复: 如果没有找到故障原因,更换线束。

    停止

  • 否 - 此时不存在该故障。

    修复: 故障可能是电气连接不良的结果。

    停止

Caterpillar Information System:

SR4 Generator with VR3 or VR4 Voltage Regulator General Information
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Stabilizer Cylinder
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Engine Shutdown Switch Circuit - Test
Machine Security System Software - Uninstall - "Immobilizer" Feature
SR4 Generator with VR3 or VR4 Voltage Regulator Lead Connections
CP-563C and CS-563C Vibratory Compactors Engine Starting
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Stabilizer Cylinder
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0190 - FMI 02
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Air Filter Restriction Lamp - Test
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Stabilizer Cylinder
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader E100 Low Engine Oil Pressure Warning
2001/10/15 New Tooling Is Available For The Assembly Of the Slack Adjusters {4261}
SR4 Generator with VR3 or VR4 Voltage Regulator Service Tools
SR4 Generator with VR3 or VR4 Voltage Regulator Troubleshooting
CP-563C and CS-563C Vibratory Compactors Engine Starting with Jump Start Cables
CP-563C and CS-563C Vibratory Compactors Engine and Machine Warm-Up
TL5 Series Field Cultivator Safety Signs and Labels
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader E190 Engine Overspeed Warning
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
CP-563C and CS-563C Vibratory Compactors Lifting and Tying Down the Machine
CP-563C and CS-563C Vibratory Compactors Cab Tilting
966G Series II and 972G Series II Wheel Loaders Engine Supplement Crankshaft Front Seal - Remove - Engine in Chassis
SR4 Generator with VR3 or VR4 Voltage Regulator Rotating Rectifier - Test
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Boom Cylinder
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.