Alternator - Disassemble - HDB Series Alternator
Disassembly Procedure
Start By:
- Remove the alternator from the machine. Refer to Disassembly and Assembly, "Alternator - Remove" for the machine that is being serviced.
Note: Before disassembly, clean the exterior of the alternator in order to prevent dirt from entering the unit.
- Remove pulley nut (2), washer (1), fan (3), and spacer (4) from the rotor shaft.
Show/hide table
Illustration 1 | g00825178 |
- Remove three bolts (5). Remove the rear cover.
Show/hide table
Illustration 2 | g00825176 |
- Remove two bolts (6). Disconnect the field winding leads from the regulator. Label the wires. Remove three bolts (7). Remove regulator (8) .
Show/hide table
Illustration 3 | g00825175 |
- Remove "B-" terminal (15) .
Show/hide table
Illustration 4 | g00825173 |
- Remove bolt (13). Remove grommet (11). Remove "R" terminal (12) .
- Loosen "B+" terminal (9). Remove four bolts (10) and disconnect the stator leads from the rectifier. Label the wires. Remove five bolts (14). Remove rectifier (16) .
- For proper alignment during assembly, mark the front frame, the stator, and the rear frame. Mark the locations of the stator leads in the rear frame. Remove four bolts (17). Separate rear frame (18) from front frame (19) .
Show/hide table
Illustration 5 | g00825170 |
- Mark the location of the field winding leads in the rear frame. Remove three bolts (20). Remove field coil (21) from the rear frame.
Show/hide table
Illustration 6 | g00825168 |
- Remove roller bearing (22) from the rear frame. The removal of this component requires force.
Show/hide table
Illustration 7 | g00825158 |
- The stator and the front frame remain marked. Remove stator (23) from the front frame.
Show/hide table
Illustration 8 | g00825156 |
- Remove rotor (24) from the front frame. The removal of this component requires force.
Show/hide table
Illustration 9 | g00825155 |
- Remove spacer (25) from the rotor.
Show/hide table
Illustration 10 | g00825154 |
- Remove three bolts (26). Remove retainer (27) .
Show/hide table
Illustration 11 | g00825149 |
- Remove ball bearing (28) from the front frame. The removal of this component requires force.
Show/hide table
Illustration 12 | g00825148 |
Caterpillar Information System:
CPT372 Truck Mounted Pumper Turbocharger - Inspect
3512B and 3512C Engines For Caterpillar Built Machines Fuel System Operation
3054 and 3056 Marine Generator Sets Reference Material
3054 and 3056 Marine Generator Sets Walk-Around Inspection
3054 and 3056 Marine Generator Sets Overhaul Considerations
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator - Assemble - HDB Series Alternator
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 147-9437 Generator through 147-9497 Generator
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 144-1811 Generator through 144-1951 Generator
3054 and 3056 Marine Generator Sets Cooling System Coolant (ELC) - Change
3512B and 3512C Engines For Caterpillar Built Machines Hydraulic Starting System
3054 and 3056 Marine Generator Sets Cooling System Coolant (DEAC) - Change
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Gear Group - Inspect
3500B and 3500 Marine Propulsion Engines with EUI Option Gauges and Indicators
Automatic Transfer Switches CTG, CTGD Series Safety Signs and Labels
330B Excavator Machine System Specifications Track Carrier Roller
3034 Marine Engine Fuel Shutoff Solenoid - Remove and Install
Automatic Transfer Switches CTG, CTGD Series Installation Information
PM820, PM822, and PM825 Cold Planer Leaving the Machine
2001/09/01 Check the Air Compressor Before Installation {1803}
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Deck Start/Run/Kill Switch
G3612 and G3616 Engines Engine Valve Lash - Inspect/Adjust
3512B and 3512C Engines For Caterpillar Built Machines Pinion Drive - Check
2001/09/01 A New Speed Sensor is Available for Some Turbocharger Groups {1052}
G3600 Engines Reference Material