Engine Oil Level - Check
Show/hide table
| NOTICE |
|---|
|
Do not under fill or overfill engine crankcase with oil. Either condition can cause engine damage. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Open the engine access door on the right rear side of the machine. The engine oil dipstick is located on the right side of the engine near the engine oil filter.
- Remove engine oil dipstick (2) and wipe the dipstick with a clean cloth. Then, insert the dipstick and remove the dipstick again. This will ensure a more accurate measurement of the engine oil level.
- While the engine is stopped, check the "ENGINE STOPPED" side of engine oil dipstick (2). Maintain the oil level between the marks on the dipstick.
- If necessary, remove oil filler plug (1) and add oil through the oil filler tube.
- Clean the oil filler plug and install the oil filler plug.
- Close the engine access door.
Show/hide table
| |
| Illustration 1 | g00791374 |
Caterpillar Information System:
TH103 Telehandler Hydraulic System Compensating System
AS2301 Screed Screed Plate (Main) - Remove and Install
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System Electronic Control Module (Autoshift)
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Diagnostic Capabilities
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Relief Valve (Hoist Raise, Hoist Lower) - Test and Adjust
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Engine Oil (High Speed) and Oil Filter - Change - If Equipped
TK1051 Track Feller Buncher Specifications
3054 Engine Automatic Timing Advance Unit - Test
769D Off-Highway Truck and 771D Quarry Truck Fuel Tank Cap and Strainer - Clean
Product Identification Numbers (PIN) Location Guide Trencher
3054 Engine Fuel Injection Nozzle - Test
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Diagnostic Code List
3054 Engine Engine Valve Lash - Inspect/Adjust
3054 Engine Valve Depth - Inspect
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Engine Oil and Filter - Change
3054 Engine Valve Guide - Inspect
TK1051 Track Feller Buncher Machine Systems Travel Motor
TK1051 Track Feller Buncher Machine System Relief Valve (Pilot)
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System Sensors
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System Solenoid Valves
2001/05/21 The Rear Axle Housing Is Now Equipped with Extra Lugs and Extra Spacers for Custom Products {3260}
Instructions for Installation of Turbine Precleaners on Products with Dust Ejectors {1055} Instructions for Installation of Turbine Precleaners on Products with Dust Ejectors {1055}
TK1051 Track Feller Buncher Ether Starting Aid Cylinder - Replace
3054 Engine Cooling System - Inspect