Correction to the Installation Procedure for the Fixed Axle Disassembly and Assembly Manual, SENR6768 {3278}
- Integrated Toolcarrier:
- IT14G (PIN: 1WN1-UP; 8ZM1-UP)
- Wheel Loader:
- 914G (PIN: 7ZM1-UP; 9WM1-UP)
The torque specification that is listed in Step 3 of the Installation Procedure on page 58 is incorrect. Insert the correct information that follows.
- Install eight washers and bolts (5) to the front axle. Tighten the bolts to 300 ± 40 N·m (220 ± 30 lb ft).
Caterpillar Information System:
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 1100 - FMI 06
2000/12/25 The Oil Seals Have Been Removed From The Exhaust Valves {1100}
RM-250C Reclaimer Mixer Propel System Load Controller - Test and Adjust
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 1100 - FMI 05
RM-250C Reclaimer Mixer Propel System Piston Pump Neutral - Test and Adjust
725 and 730 Articulated Trucks Power Train Retarder - Test
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 1100 - FMI 03
793B Off-Highway Truck Air System and Brakes Gear Pump (Torque Converter, Parking Brake Release, and Brake Cooling)
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Fan Drive Speed (Environmental Machine) - Test and Adjust
TH103 Telehandler Hydraulic System Boom Chain - Clean/Inspect/Lubricate
RM-250C Reclaimer Mixer Propel System Relief Valve (Main) - Test and Adjust
TH103 Telehandler Hydraulic System Hydraulic Oil Contamination - Test
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Piston Pump (Auxiliary) - Assemble
HF181, HF201 and HF221 Felling Heads Cutoff System
HF181, HF201 and HF221 Felling Heads Holding System
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 1227 - FMI 02
D5N Track-Type Tractor Steering Clutches and Brakes
HF181, HF201 and HF221 Felling Heads Tilt System
Installation of an Hydraulic Hand Control Conversion (Kit-Excavator Two Lever) for a Backhoe Loader{5063} Installation of an Hydraulic Hand Control Conversion (Kit-Excavator Two Lever) for a Backhoe Loader{5063}
2001/01/08 The New Version of Diagnostic Software for the LDS 3000 is Available {7620}
725 and 730 Articulated Trucks Machine Systems Secondary Steering Pump and Electric Motor - Remove
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hydraulic Accumulator (Suspension) - Test and Charge
HF181 Felling Head, HF201 Felling Head and HF221 Felling Head for Track Feller Bunchers Output Shaft - Install
3054 Engine Flywheel Housing - Inspect