2000/09/04 Caterpillar


Additional Plugs for the Collets Are Now Available {4303, 5305, 6107, 7000}

Usage:

AD40 1YZ
Load Haul Dump (LHD):
R1300 (PIN: 6QW)
R1500 (PIN: BAY)
R1600 (PIN: 9EW)
R1700 (PIN: 4LZ)
R1700G (PIN: 8XZ)
R2800 (PIN: BBR)
R2900 (PIN: BAR; 5TW)
Underground Articulated Truck (UAT):
AD40 (PIN: 1YZ)
AE40 (PIN: 1ZZ)

Description of Change: Additional plugs for the collets are now available. Prior to assembly, the additional plugs are installed on the inside of the collets in the holes for the jacking screws. The additional plugs will prevent the outside rubber bungs from being displaced by grease.

Adaptable To: The additional plugs are adaptable to the machines above. Refer to Table 1 and Illustration 1.

Table 1
Additional Service Plugs for the Collets.    
Part Number for the Plug     Plug for Jacking Screw
Thread Size    
1DE2838     Plug for 3/8 inch UNF Thread    
1DE2839     Plug for 1/2 inch UNF Thread    
1DE2840     Plug for 7/8 inch UNF Thread    
1DE2870     Plug for 1 inch UNF Thread    



Illustration 1g00738262

Typical Example

(1) Collet

(2) Plugs (three for each collet)

Caterpillar Information System:

CP-663E, CS-663E and CS-683E Vibratory Compactors Battery Disconnect Switch
Caterpillar Monitoring System MID 030 - CID 0428 - FMI 08
527 Track-Type Skidder Engine Supplement Muffler and Exhaust Extension - Remove and Install
3512 and 3516 EUI Engines for Caterpillar Built Machines Electronic Circuits
IT62G Series II Integrated Toolcarrier Diagnostic Codes (Caterpillar Monitoring System)
527 Track-Type Skidder Engine Supplement Hood - Remove and Install
Caterpillar Monitoring System MID 030 - CID 0427 - FMI 08
527 Track-Type Skidder Engine Supplement Air Cleaner - Remove and Install
725 and 730 Articulated Trucks Rollover Protective Structure (ROPS) - Inspect
C-9 Engines for Caterpillar Built Machines Cylinder Block Cover Group
IT62G Series II Integrated Toolcarrier Warning Categories (Caterpillar Monitoring System)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Axles, Differential and Brakes Visual Inspection
2000/09/04 Pilot Valves Now Have Serviceable O-Rings and Seals {4342}
527 Track-Type Skidder Engine Supplement Alternator - Remove and Install
IT62G Series II Integrated Toolcarrier Indicators
Caterpillar Monitoring System MID 030 - CID 0826 - FMI 08
2000/09/04 A Special Instruction Is Available for Installing New Wiring Harnesses on Harvester Heads {5734}
TH62, TH63, TH82 and TH83 Telehandlers Steering System Piston Pump (Implement and Steering)
725 and 730 Articulated Trucks Window Washer Reservoir - Fill
Caterpillar Monitoring System Quad Gauge Module
C-10, C-12, C-15 and C-16 Industrial Engines Diagnostic Codes
527 Track-Type Skidder Engine Supplement Turbocharger - Remove and Install
2000/09/25 The Piston Pump (Propel) and the Piston Pump (Vibratory) have Changed {5070}
2001/01/08 Replacement of Support Blocks for the Rear Axle and the Center Axle A-Frames Covered in Special Instruction, REHS0931 {3278, 7051}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.