Machine Security System Caterpillar


Key Information

Usage:

143H 1AL
可以通过配置机器安全系统来识别 255 把经过授权的钥匙。 此列表内包含用来解除机器安全系统的这些钥匙。 用户可以向此列表内添加钥匙。

ECM 可以保存用来识别每把电子钥匙的 5 个配置参数。 这些参数如下所示:

  • 说明

  • 访问级别

  • 有效期

  • ID1

  • ID2

这些参数并不保存在电子钥匙内。 下面给出了可供 Cat® 电子技师(Cat® ET)使用配置参数的完整列表:

  1. 添加一把电子钥匙。

  1. 修改与电子钥匙相关的以下信息。

    1. 访问级别

    1. 有效期

    1. 说明

  1. 删除电子钥匙。

  1. 安全解除时间

  1. 设定内部时钟。

  1. 机队配置

注: 请参阅测试和调整, "钥匙 - 编程"部分,以了解关于 6 2.a 2.b 2.c 3 和 5 项的更多信息。 请参阅系统操作, "系统解除特性"部分,以了解关于 4 项的更多信息。

注: 根据需要,可以将单把电子钥匙用在配有 MSS 的多台机器上。 每台机器无需单独的钥匙。 钥匙策略将随着机队利用率的不同而变化。 每台机器上的以下参数可能不同:说明, 访问级别 和 有效期。 所有机器上的 ID 相同。

注: 版本 2004A SP1 或以后的 Cat® ET 维修工具支持 MSS 的特性。

表 1
说明     访问级别     有效期     ID1     ID2    
操作员 2     标准     停用     58396874     52398427    
操作员 1     标准     停用     86935748     87458963    
钥匙 2     标准     00-10-24 12:00am     36454896     65842781    
钥匙 1     标准     00-6-15 6:00pm     23548719     65842781    
约翰     大     停用     0     59377777    
领工员     大     停用     23548719     36525897    

ID1 & ID2(ID &ID2)

电子钥匙内保存的 ID 为 16 位数字。 此数字在 Cat® ET 维修工具内显示为两个 8 位数字。 这些字段即所谓的 ID1 和 ID2。 通过组合这些数字便可构成完成的 ID 编号。 MSS ECM 利用此 ID 建立钥匙与钥匙列表内一组参数间的关系。

在表 1 内,第四项输入和第六项输入具有相同的 ID1。 由于 ID2 不同,因此这些钥匙依旧不同。 列表内的输入在以下各项方面可能具有相同的信息:说明, 访问级别 和 有效期。 可能为钥匙列表内的每把钥匙选择小于等于 11 个字符的说明。 列表内可能有多项输入具有相同的说明。 通过创建说明,使钥匙描述钥匙的持有者或者用户的职能。

注: 不要为电子钥匙复制说明。

访问级别

可以为钥匙列表内的钥匙指定两个访问级别之一。 级别为"标准"或"主"。 两个访问级别允许钥匙解除系统的工作。 主访问级别还授权用户利用 Cat® ET 维修工具修改机器安全系统的设定。

标准访问级别用于机器的正常工作。 应当将主访问级别限定到需要修改机器安全系统设定的那些人员。

有效期

可以为钥匙列表内的所有钥匙指定有效期。 采用特定日期的 6 小时间隔来定义此有效期。 表 1 内的第三项和第四项包含有效期。 对于表 1 内的所有其他钥匙来说,有效期列内均填写为"停用"。 "停用"表示这些项没有有效期。 机器安全系统具有内部时钟。 内部时钟超过钥匙的有效期后,对应钥匙将不再能够解除系统。 不过此项并不从钥匙列表中删除。 可以设定新的有效期,或者停用此特性。 有效期可能会与租赁合同一起使用。

注: 如果有效期结束后机器仍在工作,则机器将继续运行。 机器停运且 30 秒的计时结束时,机器将无法重新起动。

Caterpillar Information System:

Machine Security System Service Operation Using Machine Security System
Machine Security System Events
Machine Security System Diagnostic Operation
Machine Security System Key - Program
3126B Engines for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
3500 Generator Set Engines Indicators for Engine Oil Pressure
SR4 HV and SR4B HV Generators General Hazard Information
Machine Security System Protected Functions
Generator Set Control Panel for Switchgear Conversion Numeric Readout Mode
Machine Security System Operation of Status Indicator
Machine Security System Service Tools
3500 Engines For Caterpillar Built Power Modules Valve Lash and Valve Bridge Adjustment
Machine Security System Service Operation Using Service Tool
3508, 3512, and 3516 Generator Sets Overhaul (Major)
Generator Set Control Panel for Switchgear Conversion Electrical Components And Connector Locations
3500 Engines For Caterpillar Built Power Modules Visual Inspection
Machine Security System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
Machine Security System Electronic Control Module (ECM)
3508, 3512, and 3516 Generator Sets Overhaul (Top End)
Machine Security System Lost Key
3126B Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump - Remove
3126B Engines for Caterpillar Built Machines Fuel Pressure Regulator - Remove and Install
3500 Engines For Caterpillar Built Power Modules Test Tools for the Cooling System
3126B Engines for Caterpillar Built Machines Alternator - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.