IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Caterpillar


Hydrostatic Drive - Remove

Usage:

IT14G 1WN

Removal Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-7505     Transmission Jack     1    

Start By:

  1. Remove the drive shaft. Refer to Disassembly and Assembly, "Drive Shaft - Remove and Install".
  2. Remove the piston motors. Refer to Disassembly and Assembly, "Piston motor - Remove".


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Dispose of all fluids according to local regulations and mandates.


Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.




    Illustration 1g00703325

  1. Use Tooling (A) to support hydrostatic drive (1) .



    Illustration 2g00499704

  1. Remove plug (2) and drain the oil into a suitable container for storage or disposal. The capacity of the transfer drive is approximately 4 L (1 US gal).



    Illustration 3g00499707

  1. Remove bolts (3) and the washers from the back of hydrostatic drive (1). Carefully remove hydrostatic drive (1) from the front trunnion support. Lower hydrostatic drive (1) to the ground. The weight of hydrostatic drive (1) is approximately 50 kg (110 lb).

Caterpillar Information System:

C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors CID 0274 FMI 13 Atmospheric Pressure calibration required
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0273 FMI 04 Turbo Outlet Pressure short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 04 Fuel Temperature short to ground
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Install
3176C and 3196 Engines for Caterpillar Built Machines CID 0174 FMI 03 Fuel Temperature open/short to +batt
2000/05/29 Correction to Disassembly and Assembly , "Remove and Install Wheels, Bearings, and Duo-Cone Seals" {4208, 7561}
TH62, TH63, TH82 and TH83 Telehandlers Transmission Breather - Clean
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Accumulator (Refrigerant) Remove and Install
2000/06/19 Correction to Service Magazine, 9EP3441, 31 October 1999 , "New Thrust Washer Improves Service Life of Differential Group" {3258}
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Service Brakes - Remove and Install
2000/05/29 The Required Torque has been Increased for the Piston Retaining Nut in the Lift Cylinder {5102}
2000/05/29 The Required Torque has been Increased for the Piston Retaining Nut in the Tilt Cylinder {5104}
2000/06/19 Precleaner Assemblies Are Now Serviceable {1051, 1055}
TH62, TH63, TH82 and TH83 Telehandlers Transmission Neutralizer Pressure Switch - Adjust
797 Off-Highway Truck Fan Drive Hydraulic System Suction Fan
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Oil Cooler (Brake) - Install
IT28G Integrated Toolcarrier and 928G Wheel Loader Steering System Pressure Switch (Primary Steering Oil and Secondary Steering Oil)
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Refrigerant Condenser - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.