Axle Housing - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-2420     | 变速箱修复台     | 1     |
B     | 6V-2156     | 连杆支架     | 3     |
C     | 9S-9099     | 活动扳手     | 1     |
D     | 1H-3107     | 拉拔器总成     | 1     |
E     | 5F-7343     | 拉拔器总成     | 1     |
F     | 1P-0074     | 滑锤拉拔器     | 1     |
开始:
- 拆下摆动桥壳体。 请参阅拆解和组装, "摆动桥和耳轴轴承 - 拆卸"。
- 拆下固定桥壳体。 请参阅拆解和组装, "前固定桥 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
热油和热的部件可能会导致人员受伤。 同时,请勿让热的机油或热的零部件与皮肤接触。 在工作温度下,发动机冷却液是热的并且处于压力之下。 蒸汽还会引起人身伤害。 只有在停止发动机后,冷却系统的压力盖冷却到可以徒手触摸时,才能检查冷却液液位。 慢慢拧开冷却系统压力盖,以释放压力。 冷却系统添加剂含碱。 应避免皮肤和眼睛与其接触,以防造成人身伤害。 |
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 将车桥壳体放到工具 (A) 上。 车桥壳体的重量约为 498.9 kg (1100 lb)。
Show/hide table
图 1 | g00663942 |
- 利用适当的起吊设备撑住车桥壳体组件 (1) 。 拆下 12 套螺栓 (2) 和垫圈后拆下车桥壳体组件 (1) 。 车桥壳体组件 (1) 的重量约为 136.0 kg (300 lb)。
- 将车桥壳体放到工具 (A) 上,如图所示。
Show/hide table
图 2 | g00670395 |
Show/hide table
图 3 | g00670398 |
- 拆下挡圈 (4) 。
- 将螺栓 (3) 装入车桥中,如图所示。
- 将工具 (B) 安装到托架组件上,如图所示。 利用工具 (B) 和适当的起吊设备拆下托架组件 (5) 。 托架组件 (5) 的重量约为 28 kg (62 lb)。
Show/hide table
图 4 | g00670400 |
- 将两支销 (6) 打入轴 (7) 中。
Show/hide table
图 5 | g00670401 |
注: 具有外销 (6) 和内销 (6) 。
- 利用适当的压具拆下销 (7) 。 拆下齿轮 (8) 和两个垫圈 (9) 。
注: 将两支销 (6) 从轴 (7) 上拆下。
Show/hide table
图 6 | g00670403 |
- 将轴承 (10) 从齿轮 (8) 上拆下。
Show/hide table
图 7 | g00670404 |
- 对其余两个齿轮重复步骤 7 到 9。
- 利用工具 (C) 拆下螺母 (11) 。
Show/hide table
图 8 | g00670405 |
Show/hide table
图 9 | g00670407 |
- 利用工具 (B) 、工具 (D) 和适当的起吊设备拆下车桥壳体 (13) 。 车桥壳体 (13) 的重量约为 88 kg (195 lb)。
Show/hide table
图 10 | g00670410 |
- 卸下轴承内圈 (12) 。
- 利用工具 (F) 拆下轴承外圈 (15) 。
Show/hide table
图 11 | g00670661 |
- 采用以下方法之一拆卸齿圈 (16) 。 利用喷枪在定位销 (14) 处切割齿圈 (16) 。 在齿圈 (16) 内部施加三道焊缝。 这将使齿圈 (16) 收缩。
注: 拆卸齿圈 (16) 会导致齿圈损坏。
- 拆下三个定位销 (14) 。
- 拆下密封 (17) 。
Show/hide table
图 12 | g00670663 |
- 利用工具 (F) 拆下轴承外圈 (18) 。
Show/hide table
图 13 | g00670664 |
- 拆下密封件 (19) 。
Show/hide table
图 14 | g00670665 |
- 将车桥定位到工具 (A) 上,如图所示。
Show/hide table
图 15 | g00670676 |
- 利用工具 (E) 拆下轴承内圈 (20) 。
Caterpillar Information System:
Topcon® System Five Operation
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Oil Pan - Install
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Dryer (Refrigerant) - Remove and Install
IT28G Integrated Toolcarrier and 928G Wheel Loader Steering System Pressure and Flow Compensator Valve (Steering)
CS-531D, CP-533D and CS-533D Vibratory Compactors Vibratory System Piston Pump
AP-1050B and BG-245C Asphalt Pavers Safety Messages
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0253 FMI 02 Personality Module mismatch
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0254 FMI 12 Electronic Control Module Error
2000/06/12 New Parts for the Controls of the Individual Clutch Modulation (ICM) are Available {3083}
3408E and 3412E Engines for Caterpillar Built Machines Engine Sensor Open/Short Circuit - Test
2000/05/22 New Sender Assembly for the Fuel Level has Improved Service Life {1273}
TH62, TH63, TH82 and TH83 Telehandlers Radiator Screen - Clean
143H and 163H Motor Graders Before Operation
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System Solenoid Valve (Blade Lift, Lower, Tip, and Tilt) - Calibrate
AP-1050B and BG-245C Asphalt Pavers Parking
2000/06/05 New Lock Valves for the Stabilizers Keep the Cylinder Head Tight {5057, 5067, 5468}
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Differential - Disassemble
143H and 163H Motor Graders Operation
120H and 135H Motor Graders Parking
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>4P-2236</B> Generator through <B>4P-9907</B> Generator
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
2000/05/22 A New Speed Sensor has Improved Service Life {3141, 3175}
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Oscillating Axle (Rear) and Trunnion Support - Install
TH103 Telehandler Stabilizer and Cylinder Bearings - Lubricate