Bearing End Play (Output Transfer Gears) - Adjust
Show/hide table
Illustration 1 | g00731540 |
Typical Example (1) Output shaft. (2) Gear. (3) Shims. (4) Roller bearing cone. (5) Spacer. (6) Cage. |
Perform the following procedure in order to adjust the bearing end play for the output transfer gear.
- Install gear (2) on output shaft (1) .
- Heat roller bearing cone (4) to 135 °C (275 °F) for two hours. Install the roller bearing onto output shaft (1) .
- Install the output shaft assembly into the transmission case.
- Install spacer (5) onto output shaft (1) .
- Install the bearing cup, the O-ring seal and the lip seal onto cage (6). Lubricate the O-ring and the bore of the transmission case.
- Install two screw in dowel pins in the transmission case.
- Install shims (3) onto the dowel pins.
- Install cage (6) onto transmission case.
- Remove dowel pins. Install ten bolts. Torque the bolts to 105 ± 20 N·m (77 ± 15 lb ft).
- Use a magnetic base and a dial indicator in order to check end play of the output shaft. The end play on the output shaft should be 0.05 to 0.15 mm (.002 to .006 inch).
- Add or remove shims in order to achieve the correct end play.
ReferenceFor additional information on the assembly of the transmission, refer to Disassembly and Assembly, "Transmission - Assemble" for the machine that is being serviced.
Caterpillar Information System:
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0498 - FMI 03
651E and 657E Wheel Tractor-Scrapers Power Train Retarder
2000/05/01 The VIMSpc99 Software Version 1.1.7a Is Now Available {7601}
2000/05/29 New Turbocharger Oil Lines Groups {1052, 1307}
525B Wheel Skidder and 535B Wheel Skidder Power Train Transmission Clutch Running Clearance - Check
2000/05/01 Correction to Specifications Manual SENR9404 {4153}
2010/11/15 Correction to Specifications , "Pivot Shaft and Roller Frame" {4153}
D7R Series II Track-Type Tractor Rollover Protective Structure (ROPS) and Falling Object Protective Structure (FOPS) - Inspect
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-8891</B> Generator through <B>5N-8911</B> Generator
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0497 - FMI 06
2000/05/01 Correction to Specifications Manual SENR1779-01 {4153}
651E and 657E Wheel Tractor-Scrapers Power Train Selector Valve
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0498 - FMI 05
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Pinion Preload - Adjust
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0498 - FMI 06
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-9081</B> Generator through <B>5N-9432</B> Generator
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System MID 082 - CID 0498 - FMI 13
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Backlash and Bearings - Adjust
525B Wheel Skidder and 535B Wheel Skidder Power Train Axle Housing and Bearing Preload - Adjust
988G Wheel Loader Electrohydraulic System MID 082 - CID 0499 - FMI 03
651E and 657E Wheel Tractor-Scrapers Power Train Transmission Hydraulic Control Operation
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Lock Pressure - Check
D7R Series II Track-Type Tractor Transmission Breather - Clean
988G Wheel Loader Electrohydraulic System MID 082 - CID 0499 - FMI 05