Cover (Cab Rear) - Remove and Install
开始:
- 安装车斗固定销。 请参阅拆解和组装, "销(车斗固定)- 拆卸和安装"。
- 拆下将盖 (1) 固定到驾驶室中的 4 个螺栓 (2) 和硬垫圈。
- 拆下盖 (1)。 盖的重量为
15 kg (34 lb) 。
Show/hide table
图 1 | g00648253 |
注: 检查所有部件是否磨损或损坏。 如有必要,请更换部件。 利用不起毛的抹布擦拭所有部件。
- 将盖 (1) 放置在驾驶室中,如图所示。
- 安装将盖 (1) 固定到驾驶室中的 4 个螺栓 (2) 和硬垫圈。
Show/hide table
图 2 | g00648253 |
结束:
- 卸下车斗固定销。 请参阅拆解和组装, "销(车斗固定)- 拆卸和安装"。
Caterpillar Information System:
24H Motor Grader Battery Disconnect Switch
Installation Procedure for Motorized Flow Control{5051} Installation Procedure for Motorized Flow Control{5051}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Front) - Remove and Install
3114, 3116, and 3126 Engines Fuel System - Prime
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting
3034 Engine for Caterpillar Built Machines Camshaft - Install
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Assemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Disassemble
2000/04/24 Rework for Certain Rear Lamp Housing Groups {1429}
24H Motor Grader Plate Locations and Film Locations
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Electronic Technician) - Calibrate
797 Off-Highway Truck Power Train Relief Valve (Rear Axle Motor Unloader) - Disassemble
2000/04/17 The Torque For The Nuts On The Injector Wiring Harness Has Been Increased {1290}
24H Motor Grader Engine Start Switch
24H Motor Grader Drawbar Ball and Socket End Play - Check/Adjust
120H and 135H Motor Graders Circle Drive Pinion Teeth - Lubricate
3034 Engine for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3114, 3116, and 3126 Engines Fuel System Pressure - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0890 FMI 09 Telemetry Data Link Abnormal Update - Test
120H and 135H Motor Graders Circle Top - Lubricate