Air/Hydraulic Cylinder (Front Caliper) - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 1P-1856 | 挡圈钳 | 1 |
- 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要,请更换部件。
- 利用正要密封的润滑剂稍微润滑所有 O 形密封圈。
Show/hide table
图 1 g00487027 - 将两个方形密封件 (18) 安装到油缸组件 (2) 上。
- 将活塞密封件 (14) 和 O 形密封圈 (15) 安装到活塞 (12) 上。
- 安装活塞外圈弹簧和活塞外圈 (13)。
- 将活塞 (12) 和锁紧螺母 (11) 安装到连杆 (17) 上。 拧紧锁紧螺母 (11) 至扭矩为
145.5 ± 37.5 N·m (107.3 ± 27.7 lb ft) 。 - 将弹簧 (16) 安装到连杆 (17) 中。 弹簧 (16) 较小的一端应朝向油缸组件 (2) 定位。
- 将阀镶圈 (21) 和阀 (20) 安装到动力活塞 (22) 上。
- 将唇形密封 (23) 安装到动力活塞 (22) 上。
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 向下推动活塞 (12),使弹簧 (16) 缩回。
- 将带有阀 (20) 和阀镶圈 (21) 的动力活塞 (22) 安装到连杆 (17) 上。 使用工具 (A)(未显示)安装挡圈 (19)。 缓慢松开活塞 (12) 至原始位置。
Show/hide table
图 2 g00487026 - 将通风装置 (10) 安装到油缸组件 (2) 上。
Show/hide table
图 3 g00487025 - 将新的密封垫 (9)(未显示)安装到油缸组件 (2) 上。 小心放置两个半油缸组件 (2)。
Show/hide table
图 4 g00487024 - 将八个锁紧螺母 (8) 安装到油缸组件 (2) 的螺柱上。 拧紧锁紧螺母 (8) 至扭矩为
14 ± 3 N·m (124 ± 27 lb ft) 。Show/hide table图 5 g00487023 - 将排气螺钉 (4) 安装到端盖 (5) 上。 拧紧排气螺钉 (4) 至扭矩为
14 ± 3 N·m (124 ± 27 lb in) 。 - 将 O 形密封圈 (7) 安装到油缸管 (3) 的两端。 将端盖 (5) 放置到软口台钳(未显示)中。 将油缸管 (3) 安装到端盖 (5) 上。 调整端盖 (5) 一圈,底部固定在油缸管 (3) 上。 拧紧端盖 (5) 至扭矩为
14 N·m (124 lb in) 。 拧紧螺母 (6) 至扭矩为88 N·m (65 lb ft) 。Show/hide table图 6 g00487022 - 重新将油缸管 (3)放置在软口台钳(未显示)上。 将油缸组件 (2) 放置在油缸管 (3) 上。 油缸管 (3) 必须固定在油缸组件 (2) 的底部。 拧紧油缸管 (3) 至扭矩为
14 N·m (10 lb ft) 。注: 必须安装排气螺钉,使排气螺钉在储油罐端口 10 度以内。
- 拧紧螺母 (4) 至扭矩为
88 N·m (65 lb ft) 。
结束:
- 安装空气/液压油缸(前钳式)。 请参阅拆解和组装, "空气/液压油缸(前钳式)- 安装"。
Caterpillar Information System:
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Disassemble
2000/04/24 Rework for Certain Rear Lamp Housing Groups {1429}
24H Motor Grader Plate Locations and Film Locations
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission and Transfer Gears - Separate
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Assemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Install
CS-531D, CP-533D and CS-533D Vibratory Compactors Sampling Interval and Location of Sampling Valve
3034 Engine for Caterpillar Built Machines Camshaft - Remove
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Electronic Technician) - Calibrate
3034 Engine for Caterpillar Built Machines Camshaft - Install
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting
3114, 3116, and 3126 Engines Fuel System - Prime
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Front) - Remove and Install
Installation Procedure for Motorized Flow Control{5051} Installation Procedure for Motorized Flow Control{5051}
24H Motor Grader Battery Disconnect Switch
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Rear) - Remove and Install
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Time for the Transmission Clutch (Electronic Technician) - Calibrate
797 Off-Highway Truck Power Train Relief Valve (Rear Axle Motor Unloader) - Disassemble
2000/04/17 The Torque For The Nuts On The Injector Wiring Harness Has Been Increased {1290}