Service Brake (Front Caliper) - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 5P-3569 | 制动器系统活塞压具 | 1 |
B | 1P-0520 | 起子总成 | 1 |
- 安装之前先核实制动钳的所有部件清洁无异物。
- 检查所有部件有无磨损或损坏。 如有必要,请更换部件。
Show/hide table
图 1 g00481404 - 将六个密封件 (1) 和六个环 (2) 安装到前钳式行车制动器的孔中。 使用清洁的液压油润滑密封件 (1) 和环 (2)。
Show/hide table
图 2 g00481405 - 将三个罩 (3) 安装到前钳式行车制动器的孔中。 使用清洁的液压油润滑罩 (3)。
Show/hide table
图 3 g00481406 Show/hide table注意 将活塞安装到罩中时要小心操作。 确保罩位于活塞周围的槽种。
- 使用清洁的液压油润滑活塞 (4) 的外侧。 使用黄铜冲头将三个活塞 (4) 安装到前钳式行车制动器的孔中。
Show/hide table
图 4 g00481407 - 将三个罩 (5) 安装到制动钳行车制动器的孔中。 使用清洁的液压油润滑罩 (5)。
Show/hide table
图 5 g00481409 Show/hide table注意 将活塞安装到罩中时要小心操作。 确保罩位于活塞周围的槽种。
- 使用清洁的液压油润滑活塞 (6) 的外侧。 使用工具 (A) 将活塞 (6) 安装到前钳式行车制动器中。
Show/hide table
图 6 g00481411 - 松开工具 (A) 并插入工具 (B)。 继续推动活塞 (6) 至前钳式行车制动器的适当位置。 对于其余两个活塞,重复本步骤。
Show/hide table
图 7 g00481412 Show/hide table图 8 g00481413 - 将三个密封件 (7) 安装到前钳式行车制动器的孔中。 使用液压油润滑密封件 (7) 和螺塞 (8)。 使用软面锤将三个螺塞 (8) 安装到前钳式行车制动器中。
Show/hide table
图 9 g00481414 - 安装盖 (9)、八个螺栓 (10) 和硬垫圈。 拧紧螺栓 (10) 至扭矩为
510.1 ± 6.8 N·m (376.2 ± 5.0 lb ft) 。Show/hide table图 10 g00481415 - 将两个制动器衬垫组件 (13) 安装到前钳式行车制动器中。 将两个销 (12) 安装到前钳式行车制动器中。 此时用手拧紧螺栓 (11)。
结束:
- 安装前钳式行车制动器。 请参阅拆解和组装, "行车制动器(前钳式)- 安装"。
Caterpillar Information System:
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Install
CS-531D, CP-533D and CS-533D Vibratory Compactors Sampling Interval and Location of Sampling Valve
3034 Engine for Caterpillar Built Machines Camshaft - Remove
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Electronic Technician) - Calibrate
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Leveling Blade
834G Wheel Dozer and 836G Landfill Compactor Power Train Fill Pressure for the Impeller Clutch of the Torque Converter (Caterpillar Monitoring System) - Calibrate
Process for Removal and Installation of Screed Plates and Nose Bars{6640, 6643} Process for Removal and Installation of Screed Plates and Nose Bars{6640, 6643}
2000/05/08 Correction to Guideline for Reusable Parts and Salvage Operations , "Axle Housing and Final Drive Hub Salvage Procedure for 24H Motor Graders" {3260, 4050}
2000/05/15 The Flash File For The Challenger 85D Has Been Updated {7620}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Work Tool Positioner
120H and 135H Motor Graders Circle Drive Oil Level - Check
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission and Transfer Gears - Separate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Caterpillar Monitoring System) - Calibrate
834G Wheel Dozer and 836G Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
24H Motor Grader Plate Locations and Film Locations
2000/04/24 Rework for Certain Rear Lamp Housing Groups {1429}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Disassemble
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Assemble
3034 Engine for Caterpillar Built Machines Camshaft - Install
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Blade Valve and Mounting
3114, 3116, and 3126 Engines Fuel System - Prime
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Cover (Cab Front) - Remove and Install
Installation Procedure for Motorized Flow Control{5051} Installation Procedure for Motorized Flow Control{5051}