General Information (Air/Electric Starting System)
本起动系统使用一个电磁阀来控制一个空气阀以便激活空气起动马达。 如果起动马达不工作,应采取以下措施:
- 检查气压表的读数。
- 如果读数不合格,那么应使用一个外部气源向系统充气。
- 如果读数合格,那么打开主储气罐的排放阀片刻。 确认气压表的压力读数是否准确反映真实气压。 倾听有无高压放气声。
- 转动起动控制开关以激活电磁阀。 倾听有无空气起动马达小齿轮与飞轮齿圈啮合的声音。
- 如果可以听到啮合的声音,问题出在空气起动系统的空气部分。 应进行空气起动系统的空气部分中的程序。
- 如果没能听到啮合的声音,问题可能出在空气起动系统的电气部分。
Show/hide table图 1 g00286936 控制阀(典型图例)
(1) 控制阀
(2) 接头 - 在接头 (2)处断开控制阀 (1)的导线,检查电气系统。 将万用表设定在"直流电压(DCV)"档。 测量断开的连接到起动开关一侧的导线之间的电压。
- 如果测出有电压读数,说明问题出在控制阀 (2)或空气起动马达上。 进行空气起动系统的空气部分中的步骤2。
- 如果读数为"零(ZERO)",则说明问题出在控制开关或控制开关的电线上。
- 将万用表的一根导线连接到起动开关的的蓄电池接线端子上。 将另外一根导线良好接地。
- 若读数为"零(ZERO)"则说明来自蓄电池的电路断路。 这种状况,应检查断路器和接线。
- 如果控制开关测出有电压读数或者在自控制开关通向控制阀的电线上测出有电压读数,问题出在控制开关。
Show/hide table
图 2 | g00286937 |
空气起动系统(典型图例) (1) 控制阀 (2) 接头 (3) 连接 (4) 空气软管 (5) 中继阀 |
- 激活控制开关。 如果可以听到空气起动马达小齿轮与飞轮齿圈啮合的声音的话,就从中继阀 (5)的顶端拆下小空气软管 (4)。
- 当控制开关被激活时,有全压空气从空气软管 (4)的端口流出。 这就说明中继阀 (5)磨损或空气起动马达损坏。
- 如果没有压力空气自空气软管 (4)的端口流出,那么说明问题出在空气起动马达的小齿轮前壳体。
- 如果激活控制开关时没有听到空气起动马达小齿轮的声音。 但在控制阀测量到电压。 从连接 (3)将另外一个小空气软管拆下。
- 如果没有空气自拆下的空气软管的端口流出,控制阀 (1)磨损。
- 如果空气从拆下的空气软管的端口流出,那么说明问题出在空气起动马达的小齿轮前壳体。
Caterpillar Information System:
3306C Engines for Caterpillar Built Machines Battery - Test
3126B Engines Electric Starting System - Test
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Event Codes
3412C Engine Piston Ring Groove - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Valve Mechanism Cover
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0828 - FMI 08 Right Exhaust Temperature signal abnormal
3412C Engine Water Temperature Regulator - Test
3306C Engines for Caterpillar Built Machines Charging System - Test
3512B Engine for SPF343, SPS343, and SPT343 Pumpers MID 036 - CID 0336 - FMI 02 Incorrect ECS Switch inputs
3126B Engines Pinion Clearance - Adjust
3512B Petroleum Engines with the ADEM 2 Electronic Control Module MID 036 - CID 0342 - FMI 07 Secondary Speed Sensor misinstalled
3512B Petroleum Engines with the ADEM 2 Electronic Control Module MID 036 - CID 0190 - FMI 07 Primary Speed Sensor misinstalled
325D and 329D Excavators Hydraulic System Accumulator (Pilot)
3412C Engine Vibration Damper - Check
2000/03/06 Service Charts and Decals Available {0374, 0375, 7405, 7557}
3612 and 3616 Engines Fuel Injection Control Linkage
3408C, 3412C and 3412D High Performance Marine Engines Pinion Clearance - Adjust
3612 and 3616 Engines Fuel Injector
3612 and 3616 Engines Fuel Injection Cycle
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Ignore Brake/Clutch Switch Circuit - Test
3612 and 3616 Engines Aftercooler
G3500B Engines Electrohydraulic Oil Pressure - Measure - Adjustment Procedure
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Torque Limit Switch Circuit - Test
3126E Truck Engine Flywheel - Install