Diagnostic Code - Troubleshoot
The CCM has internal troubleshooting to aid in solving various system problems.
Show/hide table
CCM Error Codes | ||
CCM Error Code | Explanation | Action Required |
E00 (all bits zero) | No fault, normal operating mode | None |
E01 (bit 1 set) | Setpoint fault | CCM passwords or communication setups are corrupted. Reprogram from Connection and Setup pull-down menus. |
E02 (bit 2 set) | M50 message error | Check customer generated M50 code |
E03 (bit 3 set) | Memory backup battery is weak | Change battery. Refer to Operation and Maintenance Manual, SEBU7014, "Battery - Replace" in this manual. |
E04 (bit 4 set) | RS-232C link short circuit fault | Check RS-232C cable, PC port, and CCM port |
E05 (bit 5 set) | Internal buffer overflow on RS-232C or Data Link fault | Possibly caused by a slower than acceptable communication rate from the RS-232C port or an open CAT Data Link connection during RS-232C transmission. Increase communication rate and check CAT Data Link wires. |
E06 (bit 6 set) | Invalid CAT Data Link Message fault | Caused by:
1. Too much traffic on CAT Data Link. 2. CAT Data Link wires too long. |
E07 (bit 7 set) | Miscellaneous CAT Data Link Fault | Caused by:
1. (+/-) CAT Data Link shorted to (+/-) battery. 2. Internal hardware fault in CCM. Check CAT Data Link wiring and then replace CCM if wiring is good. |
E08 (bit 8 set) | RS-232C link message fault (parity, data size) | Check RS-232C protocol (communication rate, data bits, stop bits, parity) of CCM and host equipment. |
E.. (bits 16-9) | - | Set to zero (0). Reserved for future use. |
Caterpillar Information System:
C-10, C-12, C-15 and C-16 Industrial Engines CID 0263 FMI 04 Digital Sensor Supply short to ground
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
2000/01/31 Interactive Self-Paced Computer Training Course Available forTechnical Marketing Information (TMI) System Users {0314}
3500B and 3500B High Displacement Generator Set Engines Engine Speed/Timing Sensor - Remove and Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Utility Inverter Module - Remove and Install
C-10, C-12, C-15 and C-16 Industrial Engines CID 0263 FMI 03 Digital Sensor Supply short to +batt
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
723PLUS Digital Speed Control Installation
3512B Petroleum Engines General Information (Electronic Control System)
Customer Communication Module (CCM) for Diesel Engines System - Troubleshoot
Customer Communication Module (CCM) for Diesel Engines M5X Protocol - Troubleshoot
Customer Communication Module (CCM) for Diesel Engines Diagnostic Code - Troubleshoot
G3412C, G3508, G3512, G3516, G3606, G3608, G3612 and G3616 Engines Customer Communication Module System - Troubleshoot
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
3512B Petroleum Engines Fuel System Operation
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
723PLUS Digital Speed Control Electrical Connections
3512B Petroleum Engines Checking Engine Cylinders with an Electronic Service Tool
Alternator - Delco 21SI Alternator
3408E and 3412E Engines for Caterpillar Built Machines CID 0342 FMI 03 Secondary Engine Speed open/short to +batt
3176C and 3196 Engines for Caterpillar Built Machines CID 0545 FMI 05 Ether Start Relay open/short to +batt
3406E Generator Set Engines Fuel System Primary Filter/Water Separator - Drain
3512B Engine for SPF343, SPS343, and SPT343 Pumpers Electrical Connectors and Functions
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CID 0273 FMI 04 Turbo Outlet Pressure short to ground