Exhaust Manifold - Remove and Install
拆卸步骤
开始:
- 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。
- 将螺栓 (1) 、排气歧管 (2) 、锁和密封垫从缸盖组件上拆下。
Show/hide table
图 1 | g00652578 |
典型实例 |
- 如果发动机配备三件式排气歧管,将排气歧管 (2) 拆解为三件。
- 如有必要,从排气歧管 (2) 上拆下安装螺柱 (3) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-3931     | 防粘结剂     | 1     |
B     | 2P-2333     | 高温密封胶     | 1     |
- 在安装螺柱 (3) 的螺纹上涂抹工具 (A) 。
Show/hide table
图 2 | g00652578 |
典型实例 |
- 安装安装螺柱 (3) 。 拧紧安装螺柱 (3) 至扭矩 35 ± 5 N·m (26 ± 4 lb ft)。
- 如果发动机配备三件式排气歧管,将一薄层工具 (B) 涂敷在排气歧管 (2) 的阳性端。 将清洁的发动机机油涂抹在排气歧管 (2) 的阴性端内。 组装排气歧管 (2) ,然后去除接头上的多余密封胶。
- 安装新排气歧管密封垫。
- 将工具 (A) 涂抹到螺栓 (1) 的螺纹上。 将密封垫和排气歧管 (2) 定位到缸盖组件上。 安装锁和螺栓 (1) 。
- 按照数字顺序拧紧螺栓 (1) 至扭矩为 4 ± 1 N·m (35 ± 9 lb ft)。
Show/hide table
图 3 | g00617739 |
三件式排气歧管的典型示例 |
Show/hide table
图 4 | g00641026 |
四缸发动机的排气歧管 |
Show/hide table
图 5 | g00641092 |
水冷式排气歧管 |
- 按照数字顺序依次拧紧螺栓 (1) 到扭矩 45 ± 5 N·m (33 ± 4 lb ft)。
- 将锁片 (4) 弯曲到每个螺栓头的平面上。
Show/hide table
图 6 | g00675760 |
锁片的典型示例 |
End By: 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Multi-Torque - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Engine Temperature Sensor Open or Short Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Engine Pressure Sensor Open or Short Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Injector Solenoid Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Engine Speed/Timing Sensor - Calibrate
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Engine Speed/Timing Sensor Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines ECM Memory - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Eaton Top 2 Transmission Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Powertrain Data Link Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Cooling Fan Circuit and A/C High Pressure Switch Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test
Caterpillar Monitoring System for Electronic Modular Control Panel Pulse Width Modulated (PWM) Sensor - Test
Caterpillar Monitoring System for Electronic Modular Control Panel Sensor Signal Voltage - Test
C9 Urban Transit Bus Engine Speed/Timing Sensor
C-9 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor
3512B Marine Auxiliary Engine After Starting Engine
C-9 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor
3612 and 3616 Engines Cylinder Head - Disassemble
C-9 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor
3054B Industrial Engine Air Inlet Heater
3054B Industrial Engine Engine Oil Relief Valve
Caterpillar Monitoring System for Electronic Modular Control Panel Sensor Dynamic Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Cylinder Head - Install