Crankshaft Main Bearings - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 2P-5518     | 轴承工具     | 1     |
B     | 8T-5096     | 千分表总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 有关曲轴主轴承的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8009, "主轴承和连杆轴承"。
注: 组装之前,在曲轴主轴承上涂上清洁的发动机机油。 确保曲轴主轴承背面的锁键适合曲轴主轴承盖和缸体的凹槽。
- 使用工具 (A) ,在缸体中安装曲轴主轴承的上半部分。 不要用机油涂抹曲轴主轴承背面。
Show/hide table
图 1 | g00516920 |
- 在曲轴主轴承盖 (2) 中安装曲轴主轴承的下半部分。 不要用机油涂抹曲轴主轴承背面。
Show/hide table
图 2 | g00610152 |
- 所有 3114 发动机和早期 3116 发动机的缸体鞍座上加工有油槽。 近期的 3116 发动机和所有 3126 发动机的缸体鞍座上未加工有油槽。
Show/hide table
图 3 | g00639559 |
缸体上带有油槽的六缸发动机 |
Show/hide table
图 4 | g00639623 |
缸体上没有油槽的六缸发动机 |
Show/hide table
注意 |
---|
曲轴主轴盖安装时,应使零件号朝向发动机右侧。 曲轴主轴盖通过位于底部表面的冲压号码 1 到 7 进行识别。 止推板仅用于 6 号曲轴主轴承上。 |
- 安装轴承盖,使序号朝右。 六缸发动机按 1 到 7 的顺序(从前到后)。 四缸发动机按 1 到 5 的顺序(从前到后)。 在缸体上安放主轴承盖 (2) 到位。 将清洁的发动机机油或 Molylube 涂抹到螺栓螺纹和垫圈表面。 安装螺栓 (1) 。
- 用 54 ± 7 N·m (40 ± 5 lb ft)的扭矩拧紧螺栓 (1) 。 拧紧各个螺栓 (1) 额外 90 ± 5 度(1/4 圈)。
- 利用工具 (B) 检查曲轴的轴向间隙。 轴向间隙必须为 0.07 mm (0.003 in) 到 0.32 mm (0.013 in)。
Show/hide table
图 5 | g00517003 |
End By:
- 安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
- 将发动机平衡轴安装在 3114 发动机上。 请参阅 拆解和组装, "发动机平衡轴 - 拆卸和安装"。
Caterpillar Information System:
3612 and 3616 Engines Fuel Injector - Remove
SR4 and SR4B Generators and Control Panels Electronic Modular Control Panel II+ with Paralleling (EMCP II+P)
3056 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
3126B and 3126E On-highway Engines Accelerator Pedal (Throttle) Position Sensor Circuit - Test
3612 and 3616 Engines Valve Lifter - Assemble
3612 and 3616 Engines Valve Lifter - Disassemble
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
3612 and 3616 Engines Valve Lifter - Install
SR4 and SR4B Generators and Control Panels Before Starting Engine
3612 and 3616 Engines Valve Lifter - Remove
SR500 Generators Tools
3114, 3116, and 3126 Engines for Caterpillar Built Machines Cylinder Head - Remove
3612 and 3616 Engines Fuel Injector - Install
Caterpillar Monitoring System for Electronic Modular Control Panel CID 0102 FMI 08 Pressure Sensor (Boost) Abnormal Signal - Test
3003, 3013, 3014 and 3024 Industrial Engines Engaging the Driven Equipment
C-10 and C-12 Truck Engines Water Pump
3612 and 3616 Engines Cylinder Head - Remove
3618 Engine Crankshaft Main Bearings - Remove
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Conservation Practices
3003, 3013, 3014 and 3024 Industrial Engines Coolant Recommendations
3126B Engines for Caterpillar Built Machines Unit Injector - Remove
3524B Engines for Off-Highway Trucks Can Not Reach Top Engine RPM
3126B Marine Engine Unit Injector - Install
3126B Marine Engine Unit Injector Sleeve - Remove