Holding Arm Cylinder - Install
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Note: The HH65 Harvester Head is shown in this procedure. Other harvester heads are similar.
- Position holding arm cylinder (2) on the harvester head.
Show/hide table
Illustration 1 | g00427498 |
- Install pivot pin (3). Install the washer and the nut on pivot pin (3). Tighten the nut.
- Install pivot pin (1). Install the washer and the nut on pivot pin (1). Tighten the nut.
- Connect the two hydraulic hose assemblies on holding arm cylinder (2) .
- Place cover (4) in position on the harvester head. Install the bolts that retain cover (4) .
Show/hide table
Illustration 2 | g00463927 |
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension Cylinder (Front)
784C, 785C, 785D, 789C, 789D, 793C, 793D, 797 and 797B Off-Highway Trucks VIMS™ and Truck Payload Measurement System (TPMS) Glossary of Terms
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Holding Arm Cylinder - Remove
12H, 140H and 160H Motor Graders Power Train Transmission Oil Cooler - Remove
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Holding Arm - Install
776D and 777D Off-Highway Truck/Tractors Power Train Transmission Hydraulic System
3114, 3116, and 3126 Engines for Caterpillar Built Machines Cylinder Head - Remove
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Holding Arm - Remove
980G Wheel Loader Power Train Differential
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Throttle Position Sensor
3056 Engine for Caterpillar Built Machines Fuel System
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Tilt Cylinder - Remove
572R Pipelayer Engine Supplement Water Pump - Install
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Tilt Cylinder - Install
572R Pipelayer Engine Supplement Water Pump - Remove
3056 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
Implement Hydraulic Operations for Parallel Flow Systems{5000, 5051, 5057, 5084} Implement Hydraulic Operations for Parallel Flow Systems{5000, 5051, 5057, 5084}
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks User Defined Shutdown Input
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hydraulic Accumulator (Suspension)
3114, 3116, and 3126 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
980G Wheel Loader Power Train NoSPIN Differential
12H, 140H and 160H Motor Graders Power Train Transmission Oil Cooler - Install