C-15 and C-16 Industrial Engines Caterpillar


Cylinder Liner

Usage:

MTC855 818

C-15




Illustration 1g00288159

The following steps are for installing the cylinder liner into the cylinder block.

  1. Apply 5P-3975 Rubber Lubricant on the surfaces of the cylinder liner bore. Apply 5P-3975 Rubber Lubricant on the rubber seals on the lower part of the cylinder liner.

  1. Put the filler band completely in clean engine oil for a moment.

  1. Install the filler band (3) in the groove under the liner flange without delay.

  1. Install the liner in the bore immediately, before the filler band expands.

(1) Bore in new liner ... 137.185 ± 0.025 mm (5.4010 ± 0.0010 inch)

(2) Thickness of flange on liner ... 8.890 ± 0.020 mm (0.3500 ± 0.0008 inch)

The minimum thickness of the part that can be used again is the following value. ... 8.870 mm (0.3492 inch)

(3) Filler band

Note: Refer to Guideline For Reusable Parts, SEBF8068, "Cylinder Liners" for more information. Also, refer to Testing and Adjusting, "Cylinder Liner - Projection" for the procedure for inspecting the projection of the cylinder liners.

C-16




Illustration 2g00288159

The following steps are for installing the cylinder liner into the cylinder block.

  1. Apply 5P-3975 Rubber Lubricant on the surfaces of the cylinder liner bore. Apply 5P-3975 Rubber Lubricant on the rubber seals on the lower part of the cylinder liner.

  1. Put the filler band completely in clean engine oil for a moment.

  1. Install the filler band (3) in the groove under the liner flange without delay.

  1. Install the liner in the bore immediately, before the filler band expands.

(1) Bore in new liner ... 139.685 ± 0.025 mm (5.4994 ± 0.0010 inch)

(2) Thickness of flange on liner ... 8.890 ± 0.020 mm (0.3500 ± 0.0008 inch)

The minimum thickness of the part that can be used again is the following value. ... 8.870 mm (0.3492 inch)

(3) Filler band

Note: Refer to Guideline For Reusable Parts, SEBF8068, "Cylinder Liners" for more information. Also, refer to Testing and Adjusting, "Cylinder Liner - Projection" for the procedure for inspecting the projection of the cylinder liners.

Caterpillar Information System:

SR4 and SR4B Electric Power Generation Rewind Data Generator Identification
C-15, C-16, and C-18 Truck Engines Cylinder Block
3406E Truck Engine Engine Oil Pan
3003, 3013, 3014 and 3024 Industrial Engines Fuel System - Prime
3406E Truck Engine Compression Brake - If Equipped
C-15, C-16, and C-18 Truck Engines Valve Mechanism Cover
C-15, C-16, and C-18 Truck Engines Engine Design
3512B Marine Auxiliary Engines Turbocharger - Install
3056 Engine for Caterpillar Built Machines Connecting Rod Bearings - Remove
3003, 3013, 3014 and 3024 Industrial Engines Fuel System Primary Filter/Water Separator - Drain
C-9 Engines for Caterpillar Built Machines Engine Oil Pressure - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C-15, C-16, and C-18 Truck Engines Front Housing and Covers
3512B Marine Auxiliary Engines Air Shutoff - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Pump - Install - 3013, 3014, and 3024 Engines
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Pump - Remove - 3013, 3014, and 3024 Engines
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Before Starting Engine
3056 Engine for Caterpillar Built Machines Connecting Rod Bearings - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Check Engine Lamp or Warning Lamp Is Malfunctioning
793C and 793C XQ Off-Highway Truck Power Train Bypass Switch (Torque Converter Screen)
C-9 Engines for Caterpillar Built Machines Cooling System - Check - Overheating
C-9 Engines for Caterpillar Built Machines Cooling System - Test
C-9 Engines for Caterpillar Built Machines Water Pump - Test
3003, 3013, 3014 and 3024 Industrial Engines Cold Weather Starting
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.