Unit Injector Sleeve - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
E     | 221-9777     | 套管安装工具     | 1     |
F     | 4C-5552     | 大号膛刷     | 1     |
G     | 4C-9507     | 挡圈固定胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (F) 彻底清洁单体喷油器套管和单体喷油器孔径。
- 在 O 形密封圈 (2) 上涂抹清洁的发动机机油。 将 O 形密封圈 (2) 安装到单体喷油器套管 (1) 上。
Show/hide table
图 1 | g02021929 |
- 在工具 (E) 上定位单体喷油器套管 (1) 。
- 将一薄层工具 (G) 涂敷在单体喷油器套管 (1) 外缘的区域 (C) 。
- 在缸盖中定位单体喷油器套管 (1) 。 使用锤子在缸盖中安装单体喷油器套管 (1) 。
注: 向发动机加注燃油或冷却液之前先在 21 °C (70 °F) 下使工具 (G) 粘合两小时。 温度越低,需要的凝固时间越长。
- 向冷却系统加注冷却液到正确的液位。 请参阅操作和保养手册, "加注容量和建议"。
End By: 安装单体喷油器。 请参阅 拆解和组装, "单体喷油器 - 安装"。
Caterpillar Information System:
3500 Engines for Caterpillar Built Generator Sets Fuel Pressure Regulator
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Speed Sensor (Engine) - Adjust
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Alarm Module Control - Adjust
G3304 and G3306 Engines Governor Linkage
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines AC Voltage Range - Adjust
G3304 and G3306 Engines Governor Linkage - Woodward PSG Governor For Turbocharged Engines
C-9 Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C9 Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove
3126 Truck Engine Military Engine Lifting Bracket - Remove and Install
SR4 and SR4B Generators and Control Panels Electromechanical Control Panel with Automatic Start/Stop
3126B and 3126E On-highway Engines Factory Passwords Worksheet
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines External Potential Transformer Connections
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Starting Motor Magnetic Switch - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Pulse Width Modulated (PWM) Sensor - Test
3612 and 3616 Engines Engine Oil Filter Housings - Remove
3406E On-Highway Engine Exhaust Manifold - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Block Diagram of Generator Set Control
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3612 and 3616 Engines Engine Oil Filter Housings - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (AC Transformer Box) - Replace
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Relay Module - Replace
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Replace
SR500 Generators Bearing (Spherical Roller) - Lubricate
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Typical Generator Abbreviations