Finding Top Center Position for No. 1 Piston
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件名称 | 数量 |
A | 208-0888 | 发动机盘车工具 | 1 |
B | 350-7549 | 发动机盘车工具 | 1 |
C | 9S-9082 | 发动机盘车工具 | 1 |
D | 136-4632 | 正时销 | 1 |
E | 208-9387 | 正时销 | 1 |
F | 208-9388 | 齿座 | 1 |
使用以下步骤组装发动机正时销。
- 从正时销 (D) 开始。
Show/hide table
图 2 g02506616 拆解的 136-4632 正时销 - 拆解正时销 (D)。
Show/hide table
图 3 g02506619 比较正时销
(E) 208-9387 正时销
(F) 208-9388 齿座
(1) 销,拆卸自 136-4632 正时销 - 将正时销 (E) 和适配器 (F) 安装到正时销组件 (D) 中。 使用拆解过程中拆下的两个弹簧。
Show/hide table
图 1 | g02506600 |
(D) 136-4632 正时销 |
Show/hide table
图 4 | g01974153 |
(2) 安装有 208-9387 正时销的正时销组件 (D) |
Show/hide table
图 5 | g01925035 |
飞轮壳 (1) 正时孔 |
- 从位于飞轮壳上的正时孔中拆下螺塞 (1)。 将组装好的正时销安装到正时孔中。
注: 在特定的销售型号上,螺塞 (1) 可能位于飞轮壳相对一侧上的相同位置中。
注: 如果飞轮转过了啮合点,必须反向转动飞轮,反向意味着与发动机正常旋转方向相反的方向。 转动飞轮大约 30 度。 接着以正常旋转方向转动飞轮,直到正时销与螺纹孔啮合为止。 当 1 号活塞处于上止点位置时,此步骤可消除齿轮的齿隙。
Show/hide table图 6 g02235474 - 将工具 (A) 安装到飞轮壳左侧顶部的齿轮中。
工具 (A) 用于转动飞轮壳中的飞轮。 沿发动机旋转方向转动发动机。 从飞轮端观看发动机时,发动机旋转方向为逆时针。 转动飞轮,直到正时销与飞轮内的螺纹孔啮合为止。
注: 工具 (B) 或 (C) 也可用于转动飞轮。 根据应用和可用空间,可以使用这三个工具中的任何一个。
- 从发动机上拆下气门机构盖。
请参阅拆解和组装, KENR5159, "气门机构盖 - 拆卸和安装"。
- 如果 1 号活塞处于压缩冲程,则 1 号气缸的进气门和排气门都完全关闭。 此外,如果活塞处于压缩冲程,则可以用手移动摇臂。 如果不能移动摇臂且气门微开,则 1 号活塞处于排气冲程。
注: 当已确定实际冲程位置但需要的是另一个冲程位置时,应从飞轮上拆下正时螺栓。 随后沿发动机正常旋转方向转动飞轮 360 度并重新安装正时螺栓。
Caterpillar Information System:
C9 Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove
3126 Truck Engine Military Engine Lifting Bracket - Remove and Install
SR4 and SR4B Generators and Control Panels Electromechanical Control Panel with Automatic Start/Stop
3126B and 3126E On-highway Engines Factory Passwords Worksheet
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines External Potential Transformer Connections
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Electrical Connector - Inspect
3512B Marine Auxiliary Engine Programmable System Parameters
3126 Truck Engine Military Injection Actuation Pressure Control Valve - Assemble
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Inaccurate Display of Voltage or Current or Power - Troubleshoot
3126 Truck Engine Military Injection Actuation Pressure Control Valve - Disassemble
3126 Truck Engine Military Injection Actuation Pressure Control Valve - Install
3612 and 3616 Engines Prelube Pump Motors
G3304 and G3306 Engines Governor Linkage - Woodward PSG Governor For Turbocharged Engines
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines AC Voltage Range - Adjust
G3304 and G3306 Engines Governor Linkage
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Alarm Module Control - Adjust
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Speed Sensor (Engine) - Adjust
3500 Engines for Caterpillar Built Generator Sets Fuel Pressure Regulator
C9 Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Starting Motor Magnetic Switch - Test
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Pulse Width Modulated (PWM) Sensor - Test
3612 and 3616 Engines Engine Oil Filter Housings - Remove
3406E On-Highway Engine Exhaust Manifold - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Block Diagram of Generator Set Control