3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Caterpillar


Sensors and Electrical Connectors

Usage:

3406E 1MM

Table 1
Connector     Function    
J1/P1     ECM Connector    
J2/P2     ECM Connector    
J100/P100     Engine Coolant Temperature Sensor    
J103/P103     Intake Manifold Air Temperature Sensor    
J105/P105     Fuel Temperature Sensor    
J200/P200     Boost Pressure Sensor    
J201/P201     Engine Oil Pressure Sensor    
J203/P203     Atmospheric Pressure Sensor    
J300/P300     Injector Solenoid Harness    
J400/P400     Timing Calibration Probe    
J401/P401     Primary Engine Speed/Timing Sensor    
J402/P402     Secondary Engine Speed/Timing Sensor    
J403/P403     Accelerator Pedal Position Sensor    



Illustration 1g00995055

Diagram of components

C-10 and C-12 Engines




Illustration 2g00992601

Left side view (typical example)




Illustration 3g00992610

Top view (typical example)

3406E Engine




Illustration 4g00995059

Left side view (typical example)




Illustration 5g00995060

Right side and front views (typical example)

C-15, C-16 and C-18 Engines




Illustration 6g00992613

Left side view and top view (typical example)

Caterpillar Information System:

C9 Engine For Caterpillar Built Machines Engine Oil Filter Base - Install
G3304 and G3306 Engines Turbocharger
3126B Truck Engine Air Compressor - Remove and Install
3126B Truck Engine Fan Drive - Install
C9 Engine For Caterpillar Built Machines Engine Oil Filter Base - Remove
3126B Truck Engine Fan Drive - Remove
3126B Truck Engine Belt Tensioner - Remove and Install
3606 and 3608 Engines Engine Oil Coolers - Remove
3126B Truck Engine Idler Pulley - Install
3126B Truck Engine Idler Pulley - Remove
Caterpillar Monitoring System for Electronic Modular Control Panel Normal Mode
EMCPII+ for Gas Engines Data Link
3606 and 3608 Engines Engine Oil Coolers - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines General Information
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Service Tools
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Fault Identification
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 100 FMI 2 Pressure Sensor (Engine Oil) Incorrect Signal - Test
3612 and 3616 Engines Engine Oil Coolers - Assemble
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 110 FMI 2 Temperature Sensor (Engine Coolant) Incorrect Signal - Test
3406E Generator Set Engines Safety Signs and Labels
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test
3054 and 3056 Industrial and Generator Set Engines Lifter Group
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines CID 175 FMI 2 Temperature Sensor (Engine Oil) Incorrect Signal - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.