Water Pump - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
由于端面密封损坏,水泵可能会发生泄漏。 轴和壳体之间的相对移动可能会使传动轴接触到水泵上的端面密封。 如果发生接触,将损坏端面密封并导致过早发生故障。 |
- 安装前,请参阅专门说明书 , REHS9244,了解水泵的正确装卸步骤。
Show/hide table
图 1 g00602366 - 将适当起吊设备连在水泵 (8) 上。 水泵 (8) 的重量约为
27 kg (60 lb) 。 将水泵 (8) 定位到发动机上。 安装螺栓 (7)。Show/hide table图 2 g00602365 - 安装螺栓 (6)。
Show/hide table
图 3 g00599054 - 检查管 (3) 的 O 形密封圈。 如有必要,更换新的 O 形密封圈。 用甘油略微地润滑弯管 (5) 的孔。 将 O 形密封圈插入弯管孔中。 在弯管孔中插入管 (3)。
检查弯管 (5) 和水泵间接头密封件。 如有必要,更换新密封。 在弯管凸缘上安装密封圈。 用螺栓 (4) 将弯头 (5) 紧固到水泵上。
Show/hide table图 4 g00599053 - 检查法兰 (1) 和膨胀水箱间接头的密封垫。 如有必要,更换一个新的密封垫。 将密封垫插入法兰 (1)。 沿着管 (3) 小心地向上滑动法兰 (1)。 用螺栓 (2) 和垫圈紧固法兰 (1)。
- 向冷却系统加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Caterpillar Information System:
G3612 and G3616 Engines Generator - Remove and Install
3044C Industrial Engine Fuel Conservation Practices
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 447 FMI 12 Fuel Control Relay Failed - Test
SR4B Generators Generator - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 446 FMI 12 Air Shutoff Relay Failed - Test
G3612 and G3616 Engines Air Starting Motor - Disassemble
3114, 3116 and 3126 Engines Engine Overspeeds on Start
3034 Industrial Engine Cold Weather Starting
G3612 and G3616 Engines Air Inlet Elbow - Remove and Install
G3612 and G3616 Engines Air Inlet Choke - Assemble
3114, 3116 and 3126 Engines Engine Misfires, Knocks, or Is Unstable (at Idle Only)
G3612 and G3616 Engines Air Inlet Choke - Disassemble
G3304 and G3306 Engines Valve Cover
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Install
G3304 and G3306 Engines Valve Cover
3306C Engines for Caterpillar Built Machines Gear Group (Front)
G3304 and G3306 Engines Engine Support
Generator Set Load Sensor Droop - Adjust
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 560 FMI 11 CAT Data Link Failure Mode Not Identified - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines SP Fault Code - Troubleshoot
3512B Marine Auxiliary Engine MID 036 - CID 0289 - FMI 13 Unfiltered Fuel Pressure calibration required
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3512B Marine Auxiliary Engine MID 036 - CID 0542 - FMI 13 Unfiltered Engine Oil Pressure cal required
3512B Marine Auxiliary Engine MID 036 - CID 1335 - FMI 03 DLO Eng Filter In Press Sensor open/short to +batt