Flywheel - Inspect
飞轮端面跳动(轴向偏心度)
Show/hide table
所需工具     | ||
零件号     | 零件名称     | 数量     |
8T-5096     | 千分表总成     | 1     |
- 请参阅图 1 并安装千分表。 在读取千分表上的读数之前,在曲轴上施加一个同方向的力。 要想消除曲轴端隙。
Show/hide table
图 1 | g02509960 |
检查飞轮的端面跳动 |
- 设定千分表读数为 0.0 mm (0.00 in)。
- 以 90 度为间隔转动曲轴,读取千分表的读数。
- 记录所有四个测点的测量值。 在飞轮直径为 25.4 mm (1.0 in) 时,在所有四个点测得的高低值之差不得高于 0.13 mm (0.005 in) 的跳动量。
飞轮镗孔跳动(径向偏心度)
Show/hide table
所需工具     | ||
零件号     | 零件名称     | 数量     |
7H-1942     | 千分表     | 1     |
Show/hide table
图 2 | g02509996 |
检查飞轮的镗孔跳动 (1) 7H-1945 握杆 (2) 7H-1645 握杆 (3) 7H-1942 千分表 (4) 7H-1940 万用附件 |
- 设定千分表读数为 0.0 mm (0.00 in)。
- 以 90 度为间隔转动曲轴,读取千分表的读数。
- 记录所有四个测点的测量值。 在所有四点测得的高低值间的差值不得超过飞轮最大允许端面跳动(径向偏心度)的以下数值。
飞轮 ... 0.13 mm (0.005")
- 使用前述步骤,测量导向轴承孔跳动(偏心度)。
Show/hide table
图 3 | g02510080 |
飞轮离合器导向轴承孔 |
- 飞轮上的导向轴承孔的摆差(偏心度)不应超过以下数值:
飞轮 ... 0.13 mm (0.005")
Caterpillar Information System:
3114, 3116 and 3126 Engines Unit Injector Cranking Rack Position
C15 Petroleum Generator Set Engines Cylinder Liner Projection - Inspect
3126B Truck Engine Glossary of Electronic Control Terms
3126B Truck Engine General Information
3612 and 3616 Engines Aftercooler - Install - High Performance Aftercooler
G3612 and G3616 Engines Engine Oil Filter Housings - Install
Generator Set Load Sensor Erratic Operation of Load Sensor - Troubleshoot
Generator Set Load Sensor Undesired Speed Decrease with Load Increase - Troubleshoot
3408E and 3412E Engines for Caterpillar Built Machines Main Bearings - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod Bearings - Inspect
Generator Set Load Sensor Engine Will Not Operate in Parallel - Troubleshoot
3612 and 3616 Engines Aftercooler - Remove - Standard Aftercooler
G3612 and G3616 Engines Engine Oil Filter Housings - Disassemble
C15 Petroleum Generator Set Engines Piston Ring Groove - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Assemble
3406E Generator Set Engines Annunciator Panel - Inspect
3406E and 3456 Engines for Caterpillar Built Machines Control Valve (Compression Brake) - Test
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test
Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490} Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490}
3126B Truck Engine Electronic Control System Components
G3612 and G3616 Engines Engine Oil Pan - Remove
C-9 Engines for Caterpillar Built Machines Engine Design
3406E and 3456 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
G3612 and G3616 Engines Engine Oil Pan - Install