C15 Petroleum Generator Set Engines Caterpillar


Cylinder Liner Projection - Inspect

Usage:

C15 115
注: 下述程序在进行缸套凸出量测量时不需要使用 H 形横梁来固定缸套。

8T-0455 缸套凸出量工具组 可用来检查缸套凸出量。 更多有关如何使用此工具的信息资料,请参阅专门说明书, SMHS7727, "8T-0455 缸套凸出量千分表总成的使用"。




图 1g01096458

与缸套凸出量测量有关的部件

(1) 螺栓

(2) 垫圈

(3) 垫圈

(4) 间隔板

(5) 缸套

(6) 缸体

C13 步骤

表 1
所需工具    
零件号     零件描述     数量    
8T-0455     缸套凸出量工具总成     1    

表 2
C13 所需的部件    
项目     零件号     说明     单个缸所需的数量     六个缸所需的总数    
1     8T-4193     螺栓     6     36    
2     2S-5658     硬垫圈     6     36    
3     8F-1484     垫圈     6     36    
4     7K-1977     垫圈     6     36    

  1. 清洁缸套法兰和缸体表面。 除去缸体顶部的所有毛刺。



    图 2g01721317

    部件位置

    (1) 螺栓

    (2) 垫圈

    (3) 垫圈

    (4) 垫圈

  1. 应按照图 2 所示的顺序组装部件。 7K-1977 垫圈 (4) 由经过树脂浸渍过的棉织品制成。 垫圈不会损坏缸体的密封表面。

    注: 测量缸套凸出量之前应检查垫圈。 如果垫圈磨损或损坏,予以更换。

  1. 均匀拧紧螺栓 (1) 至扭矩为 14 N·m (10 lb ft)。



    图 3g01721370

    8T-0455 缸套凸出量工具总成

    (5) 螺栓

    (6) 千分表

    (7) 仪表体

    (8) 仪表块

  1. 松开螺栓 (5) ,直到可以移动千分表 (6) 。 在表的长侧放好表体 (7) 和千分表 (6) 。

  1. 滑动千分表 (6) 到正确位置。 千分表的指针接触表垫块 (8) 后,千分表就处于正确的位置。 滑动千分表,直到表针顺时针转动四分之一圈。 表针应在垂直位置。 拧紧螺栓 (5) ,然后把千分表归零。



    图 4g01721372

    测量缸套凸出量。

    (6) 千分表

    (7) 仪表体

  1. 在缸体隔板上放好表体 (7) 。 指针应在缸套法兰上。 读取千分表,获得缸套凸出量。 在各个缸套的四个位置(相隔 90 度)检查凸出量。

    表 3
    技术规格    
    缸套凸出量    
    0.06 至 0.18 mm (0.0024 至 0.0071 in)    
    每一缸套的最大偏差    
    0.050 mm (0.0020 in)    
    相邻缸套间的最大平均偏差    
    0.08 mm (0.0031 in)    
    所有六个缸套间的最大偏差    
    0.100 mm (0.0040 in)    

  1. 如果缸套不符合建议的缸套凸出量技术参数,则应检查以下零件:

    • 缸体孔深度应为 100.00 ± 0.03 mm (3.937 ± 0.001 in)。

    • 缸套法兰应为 100.12 ± 0.03 mm (3.942 ± 0.001 in)。

    如果缸套法兰的尺寸不符合技术参数,则应更换缸套。 然后,重复进行缸套凸出量的测量。 如果缸体孔深度尺寸不符合技术参数,则应更换缸体。 然后,重复进行缸套凸出量的测量。

C15 至 C18 步骤

表 4
所需工具    
零件号     零件描述     数量    
8T-0455     缸套凸出量工具总成     1    

表 5
C15 至 C18 所需的部件    
项目     零件号     说明     单个缸所需的数量     六个缸所需的总数    
1     7H-3598     轨条螺栓     6     36    
2     8F-1484     垫圈     6     36    
3     7K-1977     垫圈     6     36    



图 5g00443044

    注: 测量缸套凸出量前,请参阅再使用和修补指南, SEBF9390, "目视检查 3400、C15、C16 和 C18 系列发动机缸套座"了解气缸顶部平台和隔板检查步骤。

  1. 安装新的隔板衬垫和清洁的隔板。

  1. 安装垫圈。 安装所有螺栓或某一缸套周围的六个螺栓。

    螺栓扭矩 ... 95 N·m (70 lb ft)

  1. 利用 8T-0455 缸套凸出量工具组 测量 "A"、"B"、"C" 和 "D" 点的凸出量。

  1. 记录每一缸的测量值。

  1. 将每一缸的四个读数相加。 将该总和除以四以便获得平均数。

表 6
C15 至 C18 的技术规格    
缸套凸出量    
0.025 至 0.152 mm (0.0010 至 0.0060 in)    
每一缸的最大偏差    
0.051 mm (0.0020 in)    
相邻缸套间的最大平均偏差    
0.051 mm (0.0020 in)    
所有缸套间的最大偏差    
0.102 mm (0.0040 in)    

不要超过最大缸套凸出量 0.152 mm (0.006 in)。 过高的缸套凸出量将会引起缸套凸缘出现裂纹。

当缸套凸出量正确时,在缸套和隔板上作临时标记。 将缸套放到旁边。

注: 有关气缸套的正确的最终安装程序,请参阅拆解和组装, "气缸套 - 安装"。

Caterpillar Information System:

3126B Truck Engine Glossary of Electronic Control Terms
3126B Truck Engine General Information
3612 and 3616 Engines Aftercooler - Install - High Performance Aftercooler
G3612 and G3616 Engines Engine Oil Filter Housings - Install
Generator Set Load Sensor Erratic Operation of Load Sensor - Troubleshoot
Generator Set Load Sensor Undesired Speed Decrease with Load Increase - Troubleshoot
3408E and 3412E Engines for Caterpillar Built Machines Main Bearings - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod Bearings - Inspect
Generator Set Load Sensor Engine Will Not Operate in Parallel - Troubleshoot
3612 and 3616 Engines Aftercooler - Remove - Standard Aftercooler
3406E and 3456 Engines for Caterpillar Built Machines Water Pump - Test
G3612 and G3616 Engines Engine Oil Filter Housings - Remove
3114, 3116 and 3126 Engines Unit Injector Cranking Rack Position
C15 Petroleum Generator Set Engines Flywheel - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Disassemble
C15 Petroleum Generator Set Engines Piston Ring Groove - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Assemble
3406E Generator Set Engines Annunciator Panel - Inspect
3406E and 3456 Engines for Caterpillar Built Machines Control Valve (Compression Brake) - Test
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test
Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490} Installation of the 161-0797 Governor Control (Load Share Module) as Service Replacement for the 131-5459 Governor Control (Load Share Module) {4490}
3126B Truck Engine Electronic Control System Components
G3612 and G3616 Engines Engine Oil Pan - Remove
C-9 Engines for Caterpillar Built Machines Engine Design
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.