3054, 3054B and 3056 Marine Engines Caterpillar


Fuel Injection Nozzles - Install - 3056 Engine

Usage:

3056 CKS

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 1g00545200

  1. Install dust seal (5) and spacer (4) to the cylinder head.

  1. Install the new seat washer on the end of fuel injection nozzle (3) .

    Note: Remove the original seat washer from the threaded hole for the fuel injection nozzle which is located in the cylinder head. If the original seat washer is not removed, the projection of the nozzle will be incorrect when a new seat washer is installed. Do not reuse the seat washer.

  1. Install fuel injection nozzle (3) into the cylinder head.



    Illustration 2g00545199

  1. Install clamp (2) and bolts (1) to the cylinder head. Tighten bolts (1) to a torque of 12 N·m (9 lb ft).

End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".

Caterpillar Information System:

3054, 3054B and 3056 Marine Engines Fuel Injection Nozzles - Remove - 3056 Engine
EMCPII+ for Gas Engines Typical Generator Abbreviations
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Swivel - Remove
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Final Drive - Install
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Final Drive - Remove
G3612 and G3616 Engines Aftercooler - Remove
G3612 and G3616 Engines Exhaust Bypass - Remove
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Travel Motor - Install
Electronic Modular Control Panel II+ (EMCP II+) EMCP Electronic Control (Bus Transformer Box) - Replace
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Travel Motor - Remove
3500B Marine Engines Prelubrication System
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0190 - FMI 02 Loss of Engine Speed signal
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0190 - FMI 03 Engine Speed open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0190 - FMI 08 Engine Speed signal abnormal
3500B Marine Engines MID 036 - CID 0342 - FMI 03 Secondary Engine Speed open/short to +batt
3500B Marine Engines Secondary ECM/Personality Module
G3612 and G3616 Engines Aftercooler - Install
3500B Engines and 3500 Engines with EUI Option Starting Motor System
3500B Marine Engines Air Shutoff System
3512B Marine Auxiliary Engine Engine Speed/Timing Sensor - Calibrate
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Ether Starting Aid
3612 and 3616 Engines Aftercooler - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Fuel Injection Pump Housing - Disassemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.