3500B Engines Caterpillar


Auxiliary Water Pump - Install - Auxiliary Sea Water Pump

Usage:

3516B 1NW

安装步骤

表 1
需要的工具 
工具  零件号  零件描述  数量 
1P-0520  驱动器总成 


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。




    图 1g00602821

  1. 用螺栓安装齿轮 (4)以将齿轮固定在附件驱动轴上。


    图 2g00602816

  2. 如果轴承从壳体 (2)上拆下,采用以下步骤:

    1. 降低轴承温度。

    2. 使用工具 (A)安装轴承。 将轴承安装在距离壳体面 1.5 ± 0.5 mm (0.06 ± 0.02 英寸)以下的位置。 确保轴承机油孔与壳体内的机油通道对齐。

    3. 安装轴承后,测量轴承孔。 孔必须为 75 ± 0.055 mm (2.9528 ± 0.0022英寸)

  3. 确保O形密封圈就位于壳体 (2)上 用清洁的发动机机油涂在O形密封圈和轴承上。

  4. 用螺栓和垫圈 (3)安装壳体。


    图 3g00602815

  5. 将适当起吊设备连在辅助水泵 (1)上。 辅助水泵的重量约为 59 kg (130 lb)

  6. 提升辅助水泵使之进入壳体 (2)。 安装螺栓和螺母。

  7. 安装连接辅助水泵的水管。

Caterpillar Information System:

3500B Marine Engines Injector Solenoids
3500B Engines Auxiliary Water Pump - Remove - Auxiliary Sea Water Pump
3500B Engines Water Pump (Separate Circuit Aftercooler) - Assemble
3500B Engines Water Pump (Separate Circuit Aftercooler) - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Fuel Injection Pump Housing - Assemble
3500B Engines Water Pump (Separate Circuit Aftercooler) - Install
3500B Engines Water Pump (Separate Circuit Aftercooler) - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pump - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Air Inlet Heater
3612 and 3616 Engines Exhaust Manifold Shield - Remove and Install
3500B Engines Water Pump - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Aftercooler
Electronic Modular Control Panel II+ (EMCP II+) AC Factory Calibration Setpoint Programming OP5-2
Electronic Modular Control Panel II+ (EMCP II+) Parallel Setpoint Programming OP5-3
3500B Engines Auxiliary Water Pump - Disassemble - Auxiliary Sea Water Pump
G3612 and G3616 Engines Exhaust Bypass - Disassemble
797 Off-Highway Truck Power Train Final Drive
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Recoil Spring - Disassemble
G3612 and G3616 Engines Exhaust Bypass - Assemble
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Recoil Spring - Assemble
3500B Engines Auxiliary Water Pump - Assemble - Auxiliary Sea Water Pump
3500B Marine Engines Prelubrication System
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Travel Motor - Remove
Electronic Modular Control Panel II+ (EMCP II+) EMCP Electronic Control (Bus Transformer Box) - Replace
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.