Engine Oil Pump - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
B     | 8T-5096     | Dial Indicator Test Group     | 1     |
C (1)     | 256-4864     | Alignment Tool     |     |
C (2)     | 241-4232     | Alignment Tool     | 1     |
D     | 1S-0257     | Ball Peen Hammer     | 1     |
E     | 1P-0808     | Multipurpose Grease     | 1     |
Show/hide table
( 1 ) | 3003 engines |
( 2 ) | 3013, 3014 and 3024 engines |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
If the front housing is not installed, do not turn the crankshaft. Damage to the engine may occur. |
Idler Hub
- Use Tooling (C) and Tooling (D) to install idler hub (1) in the cylinder block.
Show/hide table
Illustration 1 | g01198501 |
Engine Oil Pump
- Apply Tooling (E) to the faces of inner rotor (4) and to the vanes of idler gear (3) .
Show/hide table
Illustration 2 | g00825411 |
Show/hide table
Illustration 3 | g01037617 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
- Align Timing Marks (A) and (B) that are on idler gear (3) with the respective timing marks on gears (14) and (15) . Install idler gear (3) on idler hub (1) .
- Install inner rotor (4) in idler gear (3) .
- Install the following items on idler hub (1) :
- Oil pump cover (5)
- Shim (6)
- Spring (7)
- Collar (8)
- Oil pump cover (5)
Show/hide table
Personal injury can result from the release of the spring force. The drive shaft, the piston, and the drive gear are under spring force. Use a press to slowly release the spring force before the components are removed. |
- Install retaining ring (9) on idler hub (1) .
- Use Tooling (B) in order to measure the end play of the engine oil pump. Refer to Specifications, "Engine Oil Pump".
- If the oil strainer was removed, use the following procedure for installation:
- Install O-ring seal (10) on tube assembly (11) .
Show/hide tableIllustration 4 g01037619
- Install tube assembly (11) in the cylinder block.
- Install oil strainer (13) on the cylinder block and tighten bolts (12) to a torque of 11 N·m (97 lb in).
End By:
- Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Caterpillar Information System:
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Air Inlet Heater
3612 and 3616 Engines Exhaust Manifold Shield - Remove and Install
3500B Engines Water Pump - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Aftercooler
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Refill Capacities
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Lubricant Viscosities
3500B Engines Water Temperature Regulators - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5240, 9Q-5241, 9Q-5242, 9Q-5250, 9Q-5253, 9Q-5265, 9Q-5266, 9Q-5392, 9Q-5393, 9Q-5478, 9Q-5504, 9Q-5621, 9Q-5643, 9Q-5651, 9Q-5709, 9Q-5718, 9Q-5723, 9Q-5724, 9Q-5725, 9Q-5726, 9Q-5731, 9Q-5747, 9Q-5780, 9Q-5792, 9 Final Drive Oil
CIPI UNDERCARRIAGE Arrangements: 3Q-6662; 6Z-7861, 7885, 7947, 7957, 7999; 9Q-5044, 5065, 5082, 5090, 5093, 5115, 5118, 5126, 5135, 5141, 5168, 5175, 5206, 5255, 5259, 5268, 5412, 5436, 5464, 5514, 5617, 5618, 5716, 5741, 5742, 5758, 5826, 5831, 5846 Hydraulic Oil
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Torques for Bolts on Major Components
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Standard Torque for Inch Fasteners
CIPI UNDERCARRIAGE Arrangements: 166-7047, 177-3011, 177-3553, 177-4279, 200-2995, 200-4060, 204-0808, 212-6225, 213-8653, 215-7227, 218-2237, 231-5143, 3Q-6638, 3Q-6641, 6Z-7749, 6Z-7751, 6Z-7857, 6Z-7890, 6Z-7926, 6Z-7938, 6Z-7992, 9Q-5034, 9Q-5042 Standard Torque for Metric Fasteners
3500B Engines Water Pump (Separate Circuit Aftercooler) - Remove
3500B Engines Water Pump (Separate Circuit Aftercooler) - Install
3304B and 3306B Engines for Caterpillar Built Machines Fuel Injection Pump Housing - Assemble
3500B Engines Water Pump (Separate Circuit Aftercooler) - Disassemble
3500B Engines Water Pump (Separate Circuit Aftercooler) - Assemble
3500B Engines Auxiliary Water Pump - Remove - Auxiliary Sea Water Pump
3500B Marine Engines Injector Solenoids
3500B Engines Auxiliary Water Pump - Install - Auxiliary Sea Water Pump
Electronic Modular Control Panel II+ (EMCP II+) AC Factory Calibration Setpoint Programming OP5-2
Electronic Modular Control Panel II+ (EMCP II+) Parallel Setpoint Programming OP5-3
3500B Engines Auxiliary Water Pump - Disassemble - Auxiliary Sea Water Pump
G3612 and G3616 Engines Exhaust Bypass - Disassemble