3500B Engines Caterpillar


Expansion Tank - Remove and Install

Usage:

3516B 1NW

拆卸步骤

表 1
需要的工具 
工具  零件号  零件描述  数量 
138-7573  连杆支架 


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。



    注意

    在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。

    有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。

    按照当地法规和要求处置所有液体。


  1. 从膨胀水箱将冷却液排入合适的容器以便保存或废弃这些冷却液。


    图 1g00599053

  2. 拆卸螺栓 (2)和垫圈。 沿着管 (3)小心地向下滑动法兰 ( 1)。


    图 2g00599054

  3. 拆卸螺栓 (4)、弯管 ( 5)和管 (3)。


    图 3g01055978

  4. 卸下螺栓和垫圈 ( 6)。 拆卸凸缘 (8)和管 ( 7)。


    图 4g00599056

  5. 从膨胀水箱顶部拆卸螺栓 ( 9)。 在孔中安装工具 ( A)。

  6. 将适当起吊设备连在工具 ( A)上。 膨胀水箱的重量约为 209 kg (460 lb)


    图 5g01056904

  7. 拆卸螺栓 (10)和垫圈。 拆卸膨胀水箱 (11)。

安装步骤

表 2
需要的工具 
工具  零件号  零件描述  数量 
138-7573  连杆支架 


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。




    图 6g00599056

  1. 从膨胀水箱顶部拆卸螺栓 ( 9)。 在孔中安装工具 ( A) 。

  2. 将适当起吊设备连在工具 ( A)上。 膨胀水箱的重量约为 209 kg (460 lb)


    图 7g01056904

  3. 定位膨胀水箱 (11)并安装螺栓 ( 10)和垫圈。


    图 8g00599056

  4. 拆卸工具 (A)。 在孔中安装螺栓 (9)。


    图 9g01055978

  5. 检查法兰 (8)密封件。 如有必要,换装新零件。 用甘油略微地润滑法兰 ( 8)孔。 将密封插入法兰 ( 8)。 用螺栓 (6)安装法兰 ( 8)和管 (7) 。


    图 10g00599054

  6. 检查管的O形密封圈 ( 3)。 如有必要,更换新的O形密封圈。 用甘油略微地润滑弯管 ( 5)孔。 将O形密封圈插入弯管 ( 5)孔中。 在弯管 (5)孔中插入管 ( 3)。

  7. 检查弯管 (5)和水泵间接头密封件。 如有必要,更换一个新密封件。 在弯管 (5)凸缘上安装密封圈。 用螺栓 (5)将弯头 ( 4)紧固到水泵上。


    图 11g00599053

  8. 检查法兰 (1)和膨胀水箱间接头的密封垫。 如有必要,更换一个新的密封垫。 将密封垫插入法兰 ( 1)。 沿着管 (3)小心地向上滑动法兰 ( 1) 。 用螺栓 (2)和垫圈紧固法兰 ( 1)。

  9. 加注膨胀水箱至正确液位。 对于要使用的正确冷却液,参考正在维修发动机的 操作和保养手册 。

Caterpillar Information System:

G3500 Engines Exhaust Bypass Valve - Remove and Install
3034 Engine for Caterpillar Built Machines Turbocharger - Remove
3406E and 3456 Generator Set Engines Alternator - Remove and Install
3500B Engines Electric Starting Motor - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 330 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
G3500 Engines Exhaust Manifold - Install - Water Cooled
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 269 FMI 4 Sensor Power Supply Voltage Below Normal - Test
G3500 Engines Exhaust Manifold - Remove - Water Cooled
G3606 and G3608 Engines Turbocharger - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 269 FMI 3 Sensor Power Supply Voltage Above Normal - Test
3500B Engines Alternator - Remove and Install
G3500 Engines Aftercooler - Remove and Install
G3500 Engines Exhaust Elbow - Remove and Install
3612 and 3616 Engines Water Pump
3612 and 3616 Engines Water Pump - Sea Water
G3500 Engines Exhaust Elbow - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
G3500 Engines Carburetor - Remove - High Pressure
G3500 Engines Carburetor - Remove - Low Pressure
G3606 and G3608 Engines Junction Box (Hydrax) - Remove and Install
3500B Engines Exhaust Elbow - Remove and Install
3524B Engine for Caterpillar Built Machines Crankcase Breather - Remove and Install
G3500 Engines Carburetor - Remove - Low Pressure
G3500 Engines Carburetor - Install - High Pressure
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.