Front Cover - Install
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect seal (5). If seal (5) is worn or damaged, replace the seal. Install seal (5) in front cover (2) .
Show/hide table
 | |
| Illustration 1 | g00579317 |
- Install front cover (2), button head screws (3), bolts (1), and nuts (4) .
Show/hide table
 | |
| Illustration 2 | g00591716 |
Typical example | |
- Tighten bolts (1) and nuts (4) .
Note: Do not tighten button head screws (3) until bolts (1) and nuts (4) have been properly tightened.
- Tighten button head screw (3) in the numerical sequence that is shown in Illustration 136 to the torque of 13 ± 3 N·m (10 ± 2 lb ft).
Show/hide table
 | |
| Illustration 3 | g00563307 |
Tightening sequence for button head screws | |
End By: Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Install".
Caterpillar Information System:
G3500 Engines Engine Oil Pump - Remove
3500B Engines Engine Oil Cooler - Assemble
3500B Engines Engine Oil Cooler - Disassemble
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 05 Ether Start Relay open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 06 Ether Start Relay short to ground
G3500 Engines Engine Oil Cooler - Install
3406E and 3456 Generator Set Engines Front Cover - Remove
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0248 - FMI 09 Cat Data Link not communicating
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 13 Atmospheric Pressure calibration required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 04 Atmospheric Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0263 - FMI 04 Digital Sensor Supply short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0827 - FMI 08 Left Exhaust Temperature signal abnormal
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0261 - FMI 13 Engine Timing calibration required
G3500 Engines Engine Oil Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Compression - Test
G3500 Engines Engine Oil Pump - Disassemble
3176C and 3196 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3408E and 3412E Engines for Caterpillar Built Machines Cooling System - Inspect
G3500 Engines Engine Oil Pump - Assemble
3176C and 3196 Engines for Caterpillar Built Machines Cooling System - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C15 Petroleum Generator Set Engines Water Temperature Regulator - Test
3176C and 3196 Engines for Caterpillar Built Machines Water Pump - Test