Temperature Sensor (Ambient Air) - Remove and Install
Removal Procedure
Start By:
- Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
- Connect the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
- Turn the battery disconnect switch to the OFF position.
- Remove eight bolts (1) and the washers that secure plate (2) to the platform and the cab. Use two people to remove plate (2) from the platform.
Show/hide table
Illustration 1 | g00584884 |
- Disconnect wiring harness (3) to air temperature sensor (4) at the electrical connection.
Show/hide table
Illustration 2 | g00591798 |
- Remove nut (5) that secures air temperature sensor (4) to the bracket assembly on the back of the cab.
Show/hide table
Illustration 3 | g00591799 |
- Remove air temperature sensor (4) from the bracket assembly on the back of the cab.
Installation Procedure
Note: Verify that all of the components of the air temperature sensor are clean and free of foreign material prior to installation.
- Position air temperature sensor (4) to the bracket assembly on the back of the cab.
Show/hide table
Illustration 4 | g00591799 |
- Install nut (5) that secures air temperature sensor (4) to the bracket assembly on the back of the cab.
- Connect wiring harness (3) from air temperature sensor (4) at the electrical connection.
Show/hide table
Illustration 5 | g00591798 |
- Use two people to position plate (2) to the platform. Install eight bolts (1) and the washers that secure plate (2) to the platform and the cab.
Show/hide table
Illustration 6 | g00584884 |
End By:
- Separate the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
- Remove the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Caterpillar Information System:
D9R Track-Type Tractor Air Conditioner In-Line Dryer - Replace
994D Wheel Loader Machine System VIDS/VIMS Interface Module - Remove and Install
D9R Track-Type Tractor Air Conditioner In-Line Dryer - Inspect
994D Wheel Loader Machine System Oil Filter (Front Pump Drive Lubrication) - Remove and Install
994D Wheel Loader Machine System Lubrication Pump (Automatic) - Remove and Install
3500B Engines Engine Oil Cooler - Disassemble
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 05 Ether Start Relay open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 06 Ether Start Relay short to ground
994D Wheel Loader Machine System Seat - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0248 - FMI 09 Cat Data Link not communicating
613C Series II Wheel Tractor-Scraper Hydraulic System Elevator Frame
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Install
D9R Track-Type Tractor Cooling System Water Temperature Regulator - Replace
3500B Engines Engine Oil Cooler - Assemble
Repair of Cracks in Rear Track Roller Frame{4151} Repair of Cracks in Rear Track Roller Frame{4151}
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0827 - FMI 08 Left Exhaust Temperature signal abnormal
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0261 - FMI 13 Engine Timing calibration required
545 Wheel Skidder Power Train Drive Shaft (Front) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Compression - Test
3176C and 3196 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
994D Wheel Loader Machine System Gear Pump (Steering and Brake Oil Cooler) - Assemble
545 Wheel Skidder Power Train Drive Shaft (Center) - Remove and Install
613C Series II Wheel Tractor-Scraper Hydraulic System Draft Frame
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System Calibration Operation