VIDS/VIMS Interface Module - Remove and Install
Removal Procedure
Start By:
- Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
- Connect the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
- Turn the battery disconnect switch to the OFF position.
- Remove eight bolts (1) and the washers that secure plate (2) to the platform and the cab. Use two people to remove plate (2) from the platform.
Show/hide table
Illustration 1 | g00584884 |
- Loosen the allen head screw in order to disconnect wiring harness (3) from VIDS/VIMS interface module (4) .
Show/hide table
Illustration 2 | g00591792 |
- Remove two bolts (5) and the washers that secure VIDS/VIMS interface module (4) to bar (6) .
Show/hide table
Illustration 3 | g00591793 |
- Remove two bolts (7) and the washers that secure VIDS/VIMS interface module (4) and the clip to bar (8) .
- Remove VIDS/VIMS interface module (4) from two bars (6) and (8) .
Installation Procedure
Note: Verify that all of the components of the VIDS/VIMS interface module are clean and free of foreign material prior to installation.
- Position VIDS/VIMS interface module (4) to two bars (6) and (8) .
Show/hide table
Illustration 4 | g00591793 |
- Install two bolts (7) and the washers that secure VIDS/VIMS interface module (4) and the clip to bar (8) .
- Install two bolts (5) and the washers that secure VIDS/VIMS interface module (4) to bar (6) .
- Position wiring harness (3) to VIDS/VIMS interface module (4). Tighten the allen head screw in order to secure wiring harness (3) to VIDS/VIMS interface module (4) .
Show/hide table
Illustration 5 | g00591792 |
- Use two people to position plate (2) to the platform. Install eight bolts (1) and the washers that secure plate (2) to the platform and the cab.
Show/hide table
Illustration 6 | g00584884 |
End By:
- Separate the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
- Remove the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Caterpillar Information System:
D9R Track-Type Tractor Air Conditioner In-Line Dryer - Inspect
994D Wheel Loader Machine System Oil Filter (Front Pump Drive Lubrication) - Remove and Install
994D Wheel Loader Machine System Lubrication Pump (Automatic) - Remove and Install
3500B Engines Engine Oil Cooler - Disassemble
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 05 Ether Start Relay open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 06 Ether Start Relay short to ground
994D Wheel Loader Machine System Seat - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0248 - FMI 09 Cat Data Link not communicating
613C Series II Wheel Tractor-Scraper Hydraulic System Elevator Frame
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Install
994D Wheel Loader Machine System Seat - Remove
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 13 Atmospheric Pressure calibration required
D9R Track-Type Tractor Air Conditioner In-Line Dryer - Replace
994D Wheel Loader Machine System Temperature Sensor (Ambient Air) - Remove and Install
D9R Track-Type Tractor Cooling System Water Temperature Regulator - Replace
3500B Engines Engine Oil Cooler - Assemble
Repair of Cracks in Rear Track Roller Frame{4151} Repair of Cracks in Rear Track Roller Frame{4151}
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0827 - FMI 08 Left Exhaust Temperature signal abnormal
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0261 - FMI 13 Engine Timing calibration required
545 Wheel Skidder Power Train Drive Shaft (Front) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Compression - Test
3176C and 3196 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
994D Wheel Loader Machine System Gear Pump (Steering and Brake Oil Cooler) - Assemble
545 Wheel Skidder Power Train Drive Shaft (Center) - Remove and Install