Water Pump
Show/hide table
 | |
| 图 1 | g00292733 |
典型实例 叶轮盖在图中未显示。 | |
(1) 叶轮与壳体之间的间隙 ... 0.75 ± 0.25 mm (0.030 ± 0.010 in)
(2) 密封件
(3) 密封件高度 ... 12.83 ± 0.13 mm (0.505 ± 0.005 in)
(4) 滤清器不应伸出壳体表面。
(5) 皮带轮前端面到壳体端面的尺寸 ... 103.8 ± 0.3 mm (4.09 ± 0.01 in)
注: 在一些应用中，水泵的轴上压装有法兰。 皮带轮用螺栓固定至该法兰。
法兰前端面到壳体端面的距离为如下尺寸。 ... 92.4 ± 0.3 mm (3.64 ± 0.01 in)
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Visual Inspection
3304B and 3306B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Assemble
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 General Testing and Adjusting Information
3176C and 3196 Industrial Engines Maintenance Interval Schedule
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft - Remove
3512B and 3516B Engines Engine Design
3512B and 3516B Engines Engine Design
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear) - Install
G3500 Engines Accessory Drive (Front) - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Engine Oil Filter Base
3508, 3512 and 3516 Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Operational Checks
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Belt Tensioner
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Hydraulic System Pressure - Release
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install - 3003 Engines
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove - 3003 Engines
320B, 320B L and 320B N Excavators Track Adjustment - Adjust
3116 Truck Engine Refill Capacities
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Water Temperature Regulator
3508, 3512 and 3516 Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Install