Electronic Control Module (Power Train) - Remove and Install
Removal Procedure
Start By:
- Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: For easier assembly, mark all hose assemblies, tube assemblies, wire harnesses and cables for identification purposes.
- Turn the battery disconnect switch to the OFF position.
- Remove eight bolts (1) and the washers that secure plate (2) to the platform and the cab. Use two people to remove plate (2) from the platform.
Show/hide table
Illustration 1 | g00584884 |
- Disconnect two wiring harnesses (3) and (4) from electronic control module (5) .
Show/hide table
Illustration 2 | g00584269 |
- Remove four bolts (6) and the washers that secure grounding strap (7) and electronic control module (8) to the bracket assembly on the cab. Remove electronic control module (8) from the bracket assembly on the cab.
Show/hide table
Illustration 3 | g00584270 |
- Remove eight mounts (9) and the spacers from electronic control module (8). Remove grounding strap (7) from electronic control module (8) .
Show/hide table
Illustration 4 | g00584271 |
Installation Procedure
Note: Verify that all of the components of the electronic control module are clean and free of foreign material prior to installation.
- Install grounding strap (7) to electronic control module (8). Install eight mounts (9) and the spacers to electronic control module (8) .
Show/hide table
Illustration 5 | g00584271 |
- Position electronic control module (8) to the cab. Install four bolts (6) and the washers that secure grounding strap (7) and electronic control module (8) to the bracket assembly on the cab.
Show/hide table
Illustration 6 | g00584270 |
- Connect two wiring harnesses (3) and (4) to electronic control module (5) .
Show/hide table
Illustration 7 | g00584269 |
- Use two people to position plate (2) to the platform. Install eight bolts (1) and the washers that secure plate (2) to the platform and the cab.
Show/hide table
Illustration 8 | g00584884 |
End By:
- Separate the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
- Remove the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Caterpillar Information System:
3034 Engine for Caterpillar Built Machines Flywheel - Remove
994D Wheel Loader Power Train Drive Shaft (Rear) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
D6R Series II Track-Type Tractor Hydraulic System Ripper Lift Control Valve
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
994D Wheel Loader Power Train Drive Shaft (Center) - Remove and Install
613C Series II Wheel Tractor-Scraper Braking Operation
D7R Series II Track-Type Tractor Power Train References
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Lines
D7R Series II Track-Type Tractor Hydraulic System Ripper Tip Control Valve
D11R Track-Type Tractor Fuses and Circuit Breaker - Replace/Reset
994D Wheel Loader Power Train Gear Pump (Power Train) - Remove
994D Wheel Loader Power Train Gear Pump (Power Train) - Install
3034 Engine for Caterpillar Built Machines Flywheel - Install
D7R Series II Track-Type Tractor Power Train Pressure Charts
988G Wheel Loader Axle Oil Cooler Filter - Replace
994D Wheel Loader Power Train Input Drive Shaft - Remove and Install
D6R Series II Track-Type Tractor Power Train Pressure Taps
D11R Track-Type Tractor Cooling System Coolant Extender (ELC) - Add
D11R Track-Type Tractor Cooling System Coolant (ELC) - Change
D11R Track-Type Tractor Engine Air Filter Primary Element - Replace
D10R Track-Type Tractor Engine Air Filter Primary Element - Replace
D7R Series II Track-Type Tractor Power Train Main Relief Valve - Adjust