Pistons and Connecting Rods - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 5P-3526
或 149-7180 |
活塞环压缩器 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将清洁的发动机机油涂抹在缸套孔、活塞环,以及活塞外表面上。
注: 活塞和连杆安装中,当心不要损坏缸套和/或曲轴轴颈。
- 使用工具 (A) 将活塞 (2) 和连杆装进缸套。
Show/hide table
图 2 g01096077 典型示例 - 将连杆和活塞安装到发动机中时,必须使表面 (X) 面向曲轴主轴承轴颈。 表面 (Y) 必须面对相邻连杆的表面 (Y)。
注: 表面 (X) 比表面 (Y) 厚。
注: 对表面 (X) 进行倒角加工以安装曲轴。
Show/hide table图 3 g03883658 - 安装轴承和轴承盖。
- 将清洁的发动机机油涂抹在螺母 (1) 的螺纹上。 安装螺母 (1)。
- 拧紧螺母 (1) 至扭矩为
82 ± 8 N·m (60 ± 6 lb ft) 。 将螺母 (1) 再转动 120° ± 5°。
Show/hide table
图 1 | g01032680 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 5P-3526
或 149-7180 |
活塞环压缩器 | 1 |
- 将清洁的发动机机油涂抹在缸套孔、活塞环,以及活塞外表面上。
注: 活塞和连杆安装中,当心不要损坏缸套和/或曲轴轴颈。
- 用工具 (A) 把活塞 (2) 和连杆装进钢套。
Show/hide table
图 5 g03883646 - 安装轴承和轴承盖。
注: 确保轴承凸舌与喷油管位于同一侧。
- 在螺栓 (1) 上涂抹干净的发动机机油。 安装螺栓 (1)。
- 拧紧螺栓 (1) 至扭矩为
90 ± 8 N·m (66 ± 6 lb ft) 。 将螺栓 (1) 再上紧 90° ± 5°。
Show/hide table
图 4 | g03883642 |
结束:
- 安装活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
- 安装发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 安装"。
- 安装缸盖。 请参阅拆解和组装, "缸盖 - 安装"。
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
G3500 Engines Crankshaft Main Bearings - Install
3406E On-Highway Engine Pistons and Connecting Rods - Remove
3500B High Displacement Generator Set Engines Model View Illustrations
3600 Distillate Fuel Engines Product Description
G3500 Engines Crankshaft Main Bearings - Remove
3034 Engine for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
3034 Engine for Caterpillar Built Machines Electric Starting Motor - Remove and Install
3612 and 3616 Engines Exhaust Manifold
3034 Engine for Caterpillar Built Machines Alternator - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
3612 and 3616 Engines Exhaust Manifold
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger - Remove
3408E and 3412E Engines for Caterpillar Built Machines Air in Fuel - Test
3406E On-Highway Engine Connecting Rod Bearings - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Base
3406E On-Highway Engine Connecting Rod Bearings - Install
3500 and 3500B Engines Control Panel
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
Generator Set Control Panel for Switchgear Conversion General Information
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger - Install
3406E On-Highway Engine Crankshaft Main Bearings - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines SP Fault Code - Troubleshoot
G3500 Engines Camshaft - Remove