Fuel Injection Pump - Install - Type 1 Engines and 9RM Engines
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 173-9774     | Bolt Remover (1)     | 1     |
Show/hide table
( 1 ) | The bolt remover is required in order to install the tamper proof bolts on the access cover for the fuel injection pump. |
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and Assembly, "Engine Design" topic.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect the condition of the gasket for the fuel injection pump. Replace the gasket, if necessary.
- Install the gasket and fuel injection pump (5) .
Note: Align marks (4) that are on fuel injection pump (5) and the timing gear cover.
Show/hide table
Illustration 1 | g00545262 |
- Install the key.
- Install three nuts (6) that hold fuel injection pump (5) in position.
- Connect hose (7) to fuel injection pump (5) .
- Engage the gear with the fuel injection pump.
- Install the lockwasher and nut (3) .
Show/hide table
Illustration 2 | g00545258 |
- Install cover (2) and four bolts (1) .
Note: Some engines have four tamper proof bolts (1). Use Tool (A) in order to install the four bolts.
Show/hide table
Illustration 3 | g00545256 |
- Set the timing of the fuel injection pump. Refer to the Testing and Adjusting Module for the correct procedure.
End By:
- Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install".
- Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Caterpillar Information System:
797 Off-Highway Truck Steering System Front Wheel
D350E Series II Articulated Truck Center Suspension Frame - Remove
784C and 785C Off-Highway Truck Power Train Gear Pump (Rear Axle Oil) - Assemble
988G Wheel Loader Power Train Transmission Hydraulic System
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Auxiliary Hydraulic System Gear Pump Flow - Test
3116 Engine for Challenger 35, and Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Drive Shaft - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Unswitched Power - Troubleshoot
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Fuel Solenoid - Troubleshoot
3054 Engine for Caterpillar Built Machines Fuel Injection Pump - Remove - Type 1 Engines and 9RM Engines
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Gear Shift Switch - Troubleshoot
24H Motor Grader Hydraulic and Steering System Metering Pump (Steering)
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Accessory Relay - Troubleshoot
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Wiring Harness
3054 Engine for Caterpillar Built Machines Fuel Injection Pump - Remove - Type 2 Engines and 7BJ Engines
784C and 785C Off-Highway Truck Power Train Transmission Planetary and Transfer Gears - Remove
Retrofitting the 136-7822 Transmission Control for the 109-3664 Transmission Control {3065} Retrofitting the 136-7822 Transmission Control for the 109-3664 Transmission Control {3065}
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Battery - Remove and Install
24H Motor Grader Hydraulic and Steering System Relief Valve (Steering Cylinder Crossover)
AP-1050B and BG-245C Asphalt Pavers Turbocharger - Inspect
3116 Engine for Challenger 35, and Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Engine Support - Remove and Install
D350E Series II Articulated Truck Hoist Cylinder - Remove
D400E Series II Articulated Truck Front Suspension Cylinder - Remove
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Steering Control - Assemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Mode 11 - Three-Point Hitch Status and Calibration