Inlet Manifold - Install - Type 2 Engines and 7BJ Engines
Installation Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and Assembly, "Engine Design".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect the gaskets for wear or damage. If the gaskets are worn or damaged, use new parts for replacement.
- Install the gasket and air inlet manifold (6) with bolts (5) . Tighten bolts (5) to a torque of 33 N·m (24 lb ft).
Show/hide table
 | |
| Illustration 1 | g00558245 |
Typical example | |
- Put the gasket and elbow (4) in position on the air inlet manifold.
Show/hide table
 | |
| Illustration 2 | g00557838 |
Typical example | |
- Install four bolts (2) .
- Slide the hose into position and tighten hose clamps (3) .
- Connect tube (1) to the air inlet heater.
Caterpillar Information System:
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Brake Valve Assembly - Assemble
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Auxiliary Hydraulic System Gear Pump
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Brake Valve Assembly - Disassemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Brake Valve Assembly - Install
Challenger 65C, Challenger 65D, Challenger 65E, Challenger 70C, Challenger 75C, Challenger 75D, Challenger 75E, Challenger 85C, Challenger 85D, Challenger 85E and Challenger 95E Agricultural Tractors Machine Monitor System Machine Monitor Faults
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F406 Coolant Temperature Sensor - Failed Low
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Brake Valve Assembly - Remove
3054 Engine for Caterpillar Built Machines Inlet Manifold - Remove - Type 2 Engines and 7BJ Engines
834G Wheel Tractor and 836G Landfill Compactor Braking System Gear Pump (Implement, Pilot, Brake)
988G Wheel Loader Power Train Final Drive and Wheel
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F405 Fuel Level Sensor - Failed High
3116 Engine for Challenger 35, and Challenger 45 Agricultural Tractors and 3126 Engine for Challenger 55 Agricultural Tractor Engine Supplement Water Temperature Regulator - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F407 Coolant Temperature Sensor - Failed High
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F408 Engine Oil Pressure Sensor - Failed Low
3054 Engine for Caterpillar Built Machines Water Pump - Disassemble - Type 1 Engines and 9RM Engines
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Hydraulic System Oil Level - Check
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F411 Aftercooler Temperature Sensor - Failed Low
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F412 Aftercooler Temperature Sensor - Failed High
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F413 Radar Sense Input - Not Detected
797 Off-Highway Truck Power Train Drive Shaft (Main)
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F414 Radar Signal Input - Not Detected
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Mode 4 - EMC Output Electronics
784C and 785C Off-Highway Truck Power Train Spindle - Remove
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Vibration Damper and Pulley - Remove