3054 Engine for Caterpillar Built Machines Caterpillar


Engine Oil Pan - Remove and Install

Usage:

554 1AM

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 1g01870497

    Typical Example




    Illustration 2g01871553

    Note: The engine may be equipped with an oil drain plug or the engine may be equipped with a drain valve.

  1. If equipped, remove drain plug (2) and the O-ring seal. If equipped, open drain valve (5) by turning handle (6) counterclockwise. Drain the engine oil into a suitable container for storage or disposal.

  1. If necessary, remove drain valve (5) from adapter (7) . If necessary, remove adapter (7) from engine oil pan (3) .

    Note: In order to remove a oil pan, the engine must be removed from the machine.

  1. Remove bolts (1) from engine oil pan (3) .

  1. Remove engine oil pan (3) and gasket (4) .

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Clean the gasket surfaces of the cylinder block and the engine oil pan thoroughly.



    Illustration 3g01870497

    Typical Example




    Illustration 4g01871553

  1. Install a new gasket (4) to the cylinder block. Install engine oil pan (3) .

  1. Install bolts (1) . Tighten bolts to a torque of 22 N·m (16 lb ft).

    Note: The engine may be equipped with an oil drain plug or the engine may be equipped with a drain valve.

  1. If drain valve (5) and adapter (7) were removed, use the following procedure.

    1. Install a new O-ring to the adapter (7) .

    1. Install adapter (7) into engine oil pan (3) . Tighten the adapter to a torque of 34 N·m (25 lb ft).

    1. Install a new O-ring to drain valve (5) .

    1. Install drain valve (5) into adapter (7) . Tighten the drain valve to a torque of 34 N·m (25 lb ft).

  1. If equipped, install a new O-ring seal on drain plug (2) . Install the drain plug. Tighten the drain plug to a torque of 34 N·m (25 lb ft). If equipped, close drain valve (5) by turning handle (6) clockwise. Turn handle (6) until the handle is tight. Do not overtighten the handle.

  1. Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge.

    Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for the correct engine oil capacity.

Caterpillar Information System:

3408E and 3412E Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
3406E Truck Engine Housing (Front)
3054 Engine for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
G3606 and G3608 Engines Engine Oil Pump - Remove
3054 Engine for Caterpillar Built Machines Front Cover - Install
G3606 and G3608 Engines Lubrication Metering Pump - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Front Cover - Remove and Install
3054 Engine for Caterpillar Built Machines Flywheel - Install
Guidelines For 3600 Heavy Fuel Oil (HFO) Engines{1000} Guidelines For 3600 Heavy Fuel Oil (HFO) Engines{1000}
3054 Engine for Caterpillar Built Machines Flywheel - Remove
3054 Engine for Caterpillar Built Machines Camshaft - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Water Temperature Regulator - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
3176C Engine S·O·S Oil Analysis
3176C Engine Safety Signs and Labels
3408E and 3412E Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
Generator Set Control Panel for Switchgear Conversion Action Alarm and Alarm Silence Switch
3408E and 3412E Engines for Caterpillar Built Machines Electronic Control Module - Remove and Install
3606 and 3608 Engines General Information (Fuel System)
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Temperature Sensor - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
Generator Set Control Panel for Switchgear Conversion Alert Indicator Description
Generator Set Control Panel for Switchgear Conversion Alarm Silence Switch - Troubleshoot
3054 Engine for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.