Water Manifold - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将发动机冷却液排至水歧管的水位以下。
- 将扎带和适当的起吊设备连接至水歧管 (1) 上。
Show/hide table
图 1 | g00546050 |
- 卸下涡轮增压器的水管 (3) 。
Show/hide table
图 2 | g00546051 |
- 卸下将水歧管固定至缸盖的所有螺栓 (2) 。
- 卸下四个螺栓 (4) 。
Show/hide table
图 3 | g00546052 |
- 卸下四个螺栓 (6) 。
- 卸下适配器 (5) 。
- 卸下水歧管 (1) 和密封件。 检查所有密封件是否磨损或损坏。 如有必要,更换密封件。
安装步骤
- 将扎带和适当的起吊设备连接至水歧管 (1) 上。
- 检查所有密封件是否磨损或损坏。 如有必要,更换密封件。 安装水歧管 (1) 和密封件。
- 安装适配器 (5) 。
- 安装四个螺栓 (6) 。
- 安装四个螺栓 (4) 。
- 安装将水歧管固定至缸盖的所有螺栓 (2) 。
- 安装涡轮增压器的水管 (3) 。
- 将发动机冷却液加注至适当油位。
Caterpillar Information System:
3412E and C30 Marine Engines Electronic Control System
3054 Engine for Caterpillar Built Machines Alternator - Remove and Install
3054 Engine for Caterpillar Built Machines Engine Oil Pump - Remove
3612 and 3616 Fast Vessel Engines Air Shutoff - Test
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Remove
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3412E and C30 Marine Engines Front Power Take-Off (FPTO)
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3612 and 3616 Fast Vessel Engines Engine Mounts - Check
G3606 and G3608 Engines Water Pump Seal - Install
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
3600 Heavy Fuel Engines Metal Particle Detector - Inspect
3054 Engine for Caterpillar Built Machines Engine Oil Pump - Install
3054 Engine for Caterpillar Built Machines Water Pump - Remove
Caterpillar On-Highway Diesel Engine Fluids Recommendations Conventional Coolant/Antifreeze Cooling System Maintenance
G3606 and G3608 Engines Prelubrication Oil Pump - Remove
3054 and 3056 Industrial and Generator Set Engines Water Pump - Disassemble
Electronic Modular Control Panel II+ (EMCP II+) Schematics and Wiring Diagrams
3054 Engine for Caterpillar Built Machines Water Pump - Install
G3606 and G3608 Engines Prelubrication Oil Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Install
G3606 and G3608 Engines Prelubrication Oil Pump - Disassemble
3054 Engine for Caterpillar Built Machines Camshaft Bearings - Remove and Install