Alternator - Remove and Install
Removal Procedure
- Place an index mark on all of the electrical wires that are connected to the alternator. Disconnect the electrical wires from the alternator.
- Loosen two nuts (1) from the alternator bracket.
Show/hide table
Illustration 1 | g00545984 |
Typical example |
Show/hide table
Illustration 2 | g00546048 |
Typical example |
- Loosen tension adjustment bolt (4) and slide alternator (3) toward the engine. Remove V-belt (5) from the engine.
- Remove tension adjustment bolt (4) and the washer from alternator (3) .
- Remove two nuts (1) with the washers and bolts (2) from the alternator bracket.
- Remove alternator (3) from the engine.
Installation Procedure
- Put alternator (3) in position on the engine.
Show/hide table
Illustration 3 | g00545984 |
Typical example |
Show/hide table
Illustration 4 | g00546048 |
Typical example |
- Install two bolts (2) with the washers and nuts (1) that fasten the alternator to the alternator bracket. Tighten nuts (1) finger tight. Install tension adjustment bolt (4) and the washer through the adjustment bracket and into the alternator. Do not tighten tension adjustment bolt (4) at this time.
- Put V-belt (5) in position on the engine. Adjust the tension on V-belt (5) by moving alternator (3) away from the engine. Tighten tension adjustment bolt (4) after the proper belt tension is made. For additional information on adjusting the V-belt, refer to the Specifications Module, "Belt Tension Chart" topic.
- Tighten nuts (1) in order to secure alternator (3) in position on the engine.
Caterpillar Information System:
3054 Engine for Caterpillar Built Machines Engine Oil Pump - Remove
3612 and 3616 Fast Vessel Engines Air Shutoff - Test
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Remove
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3412E and C30 Marine Engines Front Power Take-Off (FPTO)
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3612 and 3616 Fast Vessel Engines Engine Mounts - Check
G3606 and G3608 Engines Water Pump Seal - Install
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Inlet Manifold - Install
3606 and 3608 Engines Cooling System Operation
3412E and C30 Marine Engines Electronic Control System
G3606 and G3608 Engines Water Manifold - Remove and Install
3600 Heavy Fuel Engines Metal Particle Detector - Inspect
3054 Engine for Caterpillar Built Machines Engine Oil Pump - Install
3054 Engine for Caterpillar Built Machines Water Pump - Remove
Caterpillar On-Highway Diesel Engine Fluids Recommendations Conventional Coolant/Antifreeze Cooling System Maintenance
G3606 and G3608 Engines Prelubrication Oil Pump - Remove
3054 and 3056 Industrial and Generator Set Engines Water Pump - Disassemble
Electronic Modular Control Panel II+ (EMCP II+) Schematics and Wiring Diagrams
3054 Engine for Caterpillar Built Machines Water Pump - Install
G3606 and G3608 Engines Prelubrication Oil Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Install