Turbocharger - Disassemble
Disassembly Procedure
Start By:
- Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Place an index mark on all of the components for the assembly procedure.
- Remove elbow (1) and the O-ring seal.
Show/hide table
 | |
| Illustration 1 | g00545460 |
Typical example | |
- Remove two bolts (2) .
- Remove hose assembly (3) and the gasket.
- Remove six bolts (4) .
Show/hide table
 | |
| Illustration 2 | g00545463 |
Typical example | |
- Remove three clamps (5) .
- Separate compressor housing (6) from cartridge (7) .
- Remove six bolts (8) .
Show/hide table
 | |
| Illustration 3 | g00545464 |
Typical example | |
Show/hide table
 | |
| Illustration 4 | g00545505 |
Typical example | |
- Remove three clamps (9) .
- Separate cartridge (7) from turbine housing (10) .
Caterpillar Information System:
3054 Engine for Caterpillar Built Machines Turbocharger - Install
3054 Engine for Caterpillar Built Machines Turbocharger - Remove
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Cooler - Install
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Pump - Remove
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Nozzles - Install
3054 and 3056 Industrial and Generator Set Engines Fuel Injection Nozzles - Remove
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3054 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
SR4 HV and SR4B HV Generators Glossary
3412E and C30 Marine Engines Front Power Take-Off (FPTO)
3054 Engine for Caterpillar Built Machines Fuel Transfer Pump - Assemble
G3606 and G3608 Engines Water Pump Seal - Remove
3054 Engine for Caterpillar Built Machines Turbocharger - Assemble
3054 and 3056 Industrial and Generator Set Engines Inlet Manifold - Remove
3612 and 3616 Fast Vessel Engines Hourly Performance Log
3606 and 3608 Engines Cooling System Operation
3054 and 3056 Industrial and Generator Set Engines Inlet Manifold - Install
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
G3606 and G3608 Engines Water Pump Seal - Install
3612 and 3616 Fast Vessel Engines Engine Mounts - Check
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3412E and C30 Marine Engines Front Power Take-Off (FPTO)
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install