Bucket - Remove and Install
Removal Procedure
- Start the machine and position the bucket flat on the floor, as shown above.
Show/hide table
Illustration 1 | g00573664 |
- Remove two nuts (1) and bolt (2) .
- Remove pin (3) from the bucket with a brass punch.
- Remove two nuts (4) and bolt (5) .
Show/hide table
Illustration 2 | g00573667 |
- Remove pin (6) from the bucket with a brass punch.
- Remove bucket (7) from the bucket linkages and the stick. Weight of the bucket is 58 kg (128 lb).
Show/hide table
Illustration 3 | g00590484 |
Installation Procedure
Note: Be sure that the stick pin bore, bucket pin bores, and bucket pins are thoroughly clean prior to installation of the bucket.
- Apply a thin coat of 1P-0808 Multipurpose Grease on the diameter of the pin bore and the bucket pins.
Show/hide table
Illustration 4 | g00590484 |
- Position the stick in a vertical position and place bucket (7) flat on the ground, as shown above.
- Start the machine and lower the stick into bucket (7) until the pin bores are aligned with each other.
Show/hide table
Illustration 5 | g00573667 |
- Install pin (6) to the bucket linkage with a bolt (5) and two nuts (4). Tighten the bolt and nuts.
- Install pin (3) to the bucket linkage with a bolt (2) and two nuts (1). Tighten the bolt and nuts.
Show/hide table
Illustration 6 | g00573664 |
Caterpillar Information System:
302.5 Mini Hydraulic Excavator Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Blade Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Blade - Remove and Install
3054 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
M318 and M320 Excavators Machine Electronic Control System Sensors
302.5 Mini Hydraulic Excavator Engine Supplement Engine - Install
302.5 Mini Hydraulic Excavator Engine Supplement Engine - Remove
307B Excavator Supplement for 4M40 Engine Fuel Priming Pump - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Muffler - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Install
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Remove
302.5 Mini Hydraulic Excavator Engine Supplement Water Temperature Regulator - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Bucket Linkage - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Bucket Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Stick Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Stick - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Boom Cylinder - Remove and Install
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Service Meter Mode
302.5 Mini Hydraulic Excavator Machine Systems Boom - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Boom Swing Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Counterweight - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Fuel Tank - Remove
302.5 Mini Hydraulic Excavator Machine Systems Fuel Tank - Install
302.5 Mini Hydraulic Excavator Machine Systems Seat - Remove and Install