315B Excavator Excavator Systems Caterpillar


Track Roller - Disassemble

Usage:

315B L 5SW

Disassembly Procedure

Start By:

  1. Remove the track rollers. Refer to Disassembly and Assembly, "Track Roller - Remove" in this manual.

  1. Thoroughly clean the outside of the track roller prior to disassembly.


    NOTICE

    Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

    Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines.

    Dispose of all fluids according to local regulations and mandates.





    Illustration 1g00367837

  1. Drive plug (1) into the stopper in the end of the track roller. Drain the oil from the track roller into a suitable container for disposal. The capacity of the track roller is 225 ± 10 mL (7.70 ± .34 oz) .



    Illustration 2g00367838

  1. Put the track roller in a press, as shown. The weight of the track roller is 34 kg (75 lb). Press on end collar (3) . Remove retaining ring (2) . Release the pressure on the end collar. Remove end collar (3) .

  1. Remove plug (1) from the inside of the track roller.



    Illustration 3g00367844

  1. Remove Duo-cone seal kit (4) from end collar (3) .



    Illustration 4g00367852

  1. Remove the O-ring seal from shaft (5) . Remove shaft (5) from roller (6) .



    Illustration 5g00367857

  1. Remove Duo-cone seal kit (9) from end collar (8) .

  1. Remove spring pin (7) from end collar (8) and shaft (5) . Use a press to remove shaft (5) from end collar (8) . Remove the remaining O-ring seal from shaft (5) .



    Illustration 6g00367858

  1. Remove Duo-cone seal kit (10) from each end of the track roller.



    Illustration 7g00367862

  1. Use a press to remove bearing (11) from each end of the track roller.

Caterpillar Information System:

3176C and 3196 Industrial Engines Electronic Control Module - Remove and Install
A13 Auger Chain - Lubricate
315B Excavator Excavator Systems Track Carrier Roller - Assemble
A13 Auger Chain - Inspect/Adjust
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Gear - Remove and Install
5130 Excavator Hydraulic System Solenoid Valve (Bottom Dump)
5130 Excavator Hydraulic System Solenoid Valve (Swing Parking Brake)
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Disassemble
302.5 Mini Hydraulic Excavator Bucket Linkage - Lubricate
5130 Excavator Hydraulic System Solenoid Valve (Boom Float)
302.5 Mini Hydraulic Excavator Cooling System Hoses - Inspect
315B Excavator Excavator Systems Track Roller - Assemble
315B Excavator Excavator Systems Track Roller - Install
302.5 Mini Hydraulic Excavator Cooling System Coolant Level - Check
302.5 Mini Hydraulic Excavator Blade Linkage - Lubricate
302.5 Mini Hydraulic Excavator Fuel Tank Water and Sediment - Drain
5130 Excavator Hydraulic System Control Valve (Travel Parking Brake Dual Pressure)
320B Excavator Machine System Specifications Fuel Tank
320B Excavator Machine System Specifications Lines (Front)
315B Excavator Excavator Systems Track - Connect
315B Excavator Excavator Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
320B Excavator Machine System Specifications Lines (Front)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.