Camshaft Gear - Remove and Install
开始:
- 拆下凸轮轴。 请参考拆解和组装, "凸轮轴 - 拆卸"。
- 用保护罩包裹凸轮轴来防止损坏凸轮轴。
Show/hide table
图 1 g00522082 Show/hide table注意 从驱动齿轮挤压时不要使凸轮轴落到地上。 同时确认凸轮轴上的凸轮与压力板不匹配。
- 将凸轮轴 (3) 和主动齿轮 (1) 放入适当的压具内。 将凸轮轴 (3) 从主动齿轮 (1) 压出。
- 将半圆键 (2) 从凸轮轴 (3) 上拆下。
- 将半圆键 (2) 安装到凸轮轴 (3) 中。
- 提高主动齿轮 (1) 的温度。
- 将主动齿轮 (1) 安装到凸轮轴 (3) 的端口上。
- 确保半圆键 (2) 对齐。 同时确保驱动齿轮 (1) 与凸轮轴 (3) 端部上的轴肩相接触。
Show/hide table
图 2 | g00522082 |
结束:
- 安装凸轮轴。 请参阅拆解和组装, "凸轮轴 - 安装"。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Assemble
3406C (PEEC III) Truck Engines Cooling System
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal Carrier - Remove and Install
3500 Spark Ignited Engines Piston and Rings
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Install
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type I) - Disassemble
3114, 3116 and 3126 MUI Engine Governors Fuel Transfer Pump
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
3114, 3116 and 3126 MUI Engine Governors Dual Horsepower (Type VII)
3176C and 3196 Industrial Engines Compression Brake - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Gear - Remove and Install
3176C and 3196 Industrial Engines Electronic Control Module - Remove and Install
3500 Spark Ignited Engines Valve Mechanism
3406E On-Highway Engine Engine Oil Filter Base - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
3176C and 3196 Industrial Engines Compression Brake - Install
G3500B Engines Cylinder Head Valves
3406E On-Highway Engine Engine Oil Pump - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Remove
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Install
C-10 and C-12 Engines Gear Group (Front) - Remove
P16, P20, P25, P28, P40 and P60 Pulverizers Gerotor Motor - Remove