3176C and 3196 Industrial Engines Caterpillar


Compression Brake - Remove

Usage:

3196 1DW

Removal Procedure

Start By:

  1. Remove the valve mechanism covers. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g00521562

  1. Disconnect harness assembly (2) from the solenoid valve.

  2. Remove nuts (1) and bolt (3).

  3. Remove compression brake housing (4).

  4. Repeat Steps 1 through 3 for the rest of the compression brake housings.

Caterpillar Information System:

3406C (PEEC III) Truck Engines Basic Block
3114, 3116 and 3126 MUI Engine Governors Dual Horsepower (Type VI)
3114, 3116 and 3126 MUI Engine Governors Governor Bumper Spring (Some Type IV)
3114, 3116 and 3126 MUI Engine Governors Governor Bias Spring (Most Types IV, V, and VI)
G3300 Engines Governors and Actuators
3114, 3116 and 3126 MUI Engine Governors Dashpot (Types I, III, IV, V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors Governor Servo (Types I, III, IV, V, VI, and VII)
3406C (PEEC III) Truck Engines Air Inlet and Exhaust System
3114, 3116 and 3126 MUI Engine Governors Fuel Ratio Control (Types V, VI, and VII)
3114, 3116 and 3126 MUI Engine Governors Fuel Ratio Control (Types I and IV)
3176C Industrial Engine Rear Power Take-Off (RPTO) - Remove and Install
3176C and 3196 Industrial Engines Fuel Filter Base - Remove and Install
3114, 3116 and 3126 MUI Engine Governors Dual Horsepower (Type VII)
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
3114, 3116 and 3126 MUI Engine Governors Fuel Transfer Pump
3114, 3116 and 3126 MUI Engine Governors Governor (Type I) - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Remove
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Install
3500 Spark Ignited Engines Piston and Rings
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal Carrier - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Disassemble
3406C (PEEC III) Truck Engines Cooling System
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Gear - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.