Cab - Install
Installation Procedure
- Be sure that the original washers are located on the mounting pads for the cab.
Show/hide table
Illustration 1 | g00633801 |
- The approximate weight of the cab is 681 kg (1500 lb). Attach a suitable lifting device to cab (42) and place the cab in position on the machine.
- Install the plates and bolts (41). Tighten the bolts to a torque of 475 ± 53 N·m (350 ± 39 lb ft).
Show/hide table
Illustration 2 | g00633800 |
- Install handle (40) on the control.
- Install the plates and bolts (39). Tighten the bolts to a torque of 475 ± 53 N·m (350 ± 39 lb ft).
Show/hide table
Illustration 3 | g00633799 |
- Connect hose assemblies (36), (37), and (38) .
Show/hide table
Illustration 4 | g00633798 |
- Connect rod end (35) for the governor control linkage to the lever.
Show/hide table
Illustration 5 | g00633796 |
- Connect wiring harness (33). Connect two wires (34) to the starter.
Show/hide table
Illustration 6 | g00633794 |
- Connect wiring harness (29). Use bolt (28) to install the clip for the harness.
Show/hide table
Illustration 7 | g00633792 |
- Connect wires (30). Connect wiring harnesses (31) and (32) .
- Connect wiring harness (27) .
Show/hide table
Illustration 8 | g00633793 |
- Connect wiring harness (25). Connect battery circuit cable (26) to the disconnect switch.
Show/hide table
Illustration 9 | g00633791 |
- Connect four hoses (24) to the washer fluid bottle.
Show/hide table
Illustration 10 | g00633789 |
- Connect ground wire (22) and wiring harness (23) .
- Connect two rod ends (21) for the linkage for speed and direction control.
Show/hide table
Illustration 11 | g00633788 |
- Connect rod ends (19) and (20) for the transmission control linkage to the levers.
Show/hide table
Illustration 12 | g00633787 |
- Connect rod end (18) for the brake control linkage to the lever. Connect rod end (17) for the steering control linkage to the lever.
Show/hide table
Illustration 13 | g00633785 |
- Connect wiring harness (16). Use bolt (15) to install the clip for the harness.
- Connect rod end (14) for the parking brake control linkage to the control valve.
Show/hide table
Illustration 14 | g00633784 |
- Connect five wiring harnesses (13) that are located on top of the flywheel housing.
Show/hide table
Illustration 15 | g00633783 |
- Place the drain hose for the air conditioner in position and tighten hose clamp (12) .
Show/hide table
Illustration 16 | g00633782 |
- Position the two heater hoses on the heater core and tighten hose clamps (11) .
- Connect two hose assemblies (10) to the evaporator core.
- Install covers (7), (8), and (9) .
Show/hide table
Illustration 17 | g00633780 |
- Install two bulkheads (6) in cover (7) .
Show/hide table
Illustration 18 | g00633779 |
- Install covers (2), (3), (4), and (5) .
Show/hide table
Illustration 19 | g00633778 |
- Install floorplate (1) .
Show/hide table
Illustration 20 | g00633777 |
- Charge the air conditioning system. Refer to the Air Conditioning and Heating Service Manual, SENR5664 for the correct procedure to charge the system.
End By:
- Install the rollover protective structure (ROPS).
- Install the hood. Refer to the Disassembly and Assembly ManualSENR9418, "Hood - Remove and Install".
Caterpillar Information System:
527 Track-Type Skidder Machine Supplements Cab - Remove
527 Track-Type Skidder Machine Supplements Rollover Protective Structure (ROPS, Enclosed Cab) - Remove and Install
527 Track-Type Skidder Machine Supplements Rollover Protective Structure (ROPS, Open Cab) - Remove and Install
527 Track-Type Skidder Machine Supplements Sweeps - Remove and Install
527 Track-Type Skidder Machine Supplements Receiver-Dryer - Remove and Install
527 Track-Type Skidder Machine Supplements Refrigerant Evaporator Coil and Heater Core - Install
527 Track-Type Skidder Machine Supplements Refrigerant Evaporator Coil and Heater Core - Remove
527 Track-Type Skidder Machine Supplements Refrigerant Condenser Fans and Motor - Remove and Install
527 Track-Type Skidder Machine Supplements Refrigerant Condenser - Remove and Install
527 Track-Type Skidder Machine Supplements Refrigerant Compressor - Remove and Install
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Wheel Nuts - Tighten
527 Track-Type Skidder Machine Supplements Governor Control Linkage - Adjust
527 Track-Type Skidder Machine Supplements Seat - Remove and Install
527 Track-Type Skidder Machine Supplements Bulldozer Blade (Power Angle and Tilt) - Remove and Install
527 Track-Type Skidder Machine Supplements Bulldozer Blade (Power Angle) - Remove and Install
527 Track-Type Skidder Machine Supplements Bulldozer Singletree - Remove and Install
527 Track-Type Skidder Machine Supplements Bulldozer C-Frame - Remove
527 Track-Type Skidder Machine Supplements Bulldozer C-Frame - Install
527 Track-Type Skidder Machine Supplements Bulldozer Lift Cylinder - Remove
527 Track-Type Skidder Machine Supplements Bulldozer Lift Cylinder - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Three-Point Hitch Relief Valve
3176C and 3196 Engines For Caterpillar Built Machines Electronic Control Module - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Air Conditioner - Install
554 Forwarder and 574 Forwarder Articulation Bearings - Lubricate