527 Track-Type Skidder Machine Supplements Caterpillar


Refrigerant Condenser - Remove and Install

Usage:

527 2RS

Removal Procedure


NOTICE

Effective July 1, 1992 regulations prohibit the venting of any refrigerant into the atmosphere. Refer to Caterpillar publications Service Manuals, SENR3334, SENR5664, and NEDG5065 for the proper procedure, the proper equipment, and the proper tools needed in order to reclaim refrigerant from any Caterpillar equipment.


------ WARNING! ------

Personal injury can result from contact with refrigerant.

Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.

Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.

Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.

Personal injury or death can result from inhaling refrigerant through a lit cigarette.

Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.

Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.

Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.

----------------------



    Illustration 1g00633202

  1. Remove bolts (1) and guard assembly (2) .



    Illustration 2g00633205

    Note: The air conditioning lines are equipped with a check valve. The air conditioning system does not need to be evacuated in order to disconnect lines (4) .

  1. Disconnect tube assemblies (4) from condenser (5) .

Installation Procedure




    Illustration 3g00633205

  1. Put condenser (5) in position and install bolts (3) .

  1. Replace the O-Ring seals at two tube assemblies (4) and connect the tube assemblies to condenser (5) .



    Illustration 4g00633202

  1. Put guard assembly (2) in position and install bolts (1) .

  1. Charge the air conditioning system, if necessary.

Note: Refer to the Air Conditioning and Heating Service Manual, SENR5664 for the correct procedure to charge the system.

Caterpillar Information System:

527 Track-Type Skidder Machine Supplements Refrigerant Compressor - Remove and Install
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Wheel Nuts - Tighten
527 Track-Type Skidder Machine Supplements Governor Control Linkage - Adjust
527 Track-Type Skidder Machine Supplements Governor Control Linkage and Decelerator - Assemble
824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Piston Motor (Fan Drive)
793C Off-Highway Truck/Tractor Power Train Lockup Clutch and Synchronizing Valve - Assemble
527 Track-Type Skidder Machine Supplements Governor Control Linkage and Decelerator - Disassemble
527 Track-Type Skidder Machine Supplements Governor Control Linkage and Decelerator - Install
527 Track-Type Skidder Machine Supplements Governor Control Linkage and Decelerator - Remove
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Three-Point Hitch Control Valve
527 Track-Type Skidder Machine Supplements Bulldozer Control Valve - Assemble
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission and Transfer Gears - Remove
527 Track-Type Skidder Machine Supplements Refrigerant Condenser Fans and Motor - Remove and Install
527 Track-Type Skidder Machine Supplements Refrigerant Evaporator Coil and Heater Core - Remove
527 Track-Type Skidder Machine Supplements Refrigerant Evaporator Coil and Heater Core - Install
527 Track-Type Skidder Machine Supplements Receiver-Dryer - Remove and Install
527 Track-Type Skidder Machine Supplements Sweeps - Remove and Install
527 Track-Type Skidder Machine Supplements Rollover Protective Structure (ROPS, Open Cab) - Remove and Install
527 Track-Type Skidder Machine Supplements Rollover Protective Structure (ROPS, Enclosed Cab) - Remove and Install
527 Track-Type Skidder Machine Supplements Cab - Remove
527 Track-Type Skidder Machine Supplements Cab - Install
527 Track-Type Skidder Machine Supplements Seat - Remove and Install
527 Track-Type Skidder Machine Supplements Bulldozer Blade (Power Angle and Tilt) - Remove and Install
527 Track-Type Skidder Machine Supplements Bulldozer Blade (Power Angle) - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.