Governor Control Linkage and Decelerator - Disassemble
Disassembly Procedure
Start By:
- Remove the governor control linkage and decelerator.
- Loosen bolt (2) and remove lever (1) from the shaft. Remove the key from the shaft.
Show/hide table
Illustration 1 | g00631790 |
- Remove housing (5) and the washer from cover assembly (4) .
Show/hide table
Illustration 2 | g00631792 |
- Remove bolts (6). Remove cover assembly (4), plate assembly (3), and two gaskets from the support.
- Remove rollers (8) and springs (7) from the plate assembly.
Show/hide table
Illustration 3 | g00631793 |
- Remove plate assembly (10) from cover assembly (4) .
Show/hide table
Illustration 4 | g00631794 |
- Remove spring (9) from the shaft assembly.
- Remove shaft assembly (12) and spring (11) from cover assembly (4) .
Show/hide table
Illustration 5 | g00631795 |
- Loosen bolt (14) and remove lever (13) from the shaft assembly.
Show/hide table
Illustration 6 | g00631796 |
- Remove the key from the shaft assembly.
- Remove the cotter pin and pin (17). Disconnect bar (16) from pedal (15) .
Show/hide table
Illustration 7 | g00631797 |
- Remove bolt (19) and lever (18) .
Show/hide table
Illustration 8 | g00631799 |
- Remove the key from shaft assembly (20). Remove the shaft assembly from the support.
- Loosen bolt (21). Remove shaft (22) and pedal (15) from the support.
Show/hide table
Illustration 9 | g00631801 |
- Loosen bolt (23) and remove pedal (24) from the shaft.
Show/hide table
Illustration 10 | g00631803 |
- Loosen bolt (28) and slide shaft (25) out of lever (27). Remove key (26) from shaft (25). Remove the shaft and lever (27) from the support.
Show/hide table
Illustration 11 | g00631804 |
- If necessary, remove bearings (30) and seals (31) from support (29) .
Show/hide table
Illustration 12 | g00631805 |
Caterpillar Information System:
527 Track-Type Skidder Machine Supplements Governor Control Linkage and Decelerator - Install
527 Track-Type Skidder Machine Supplements Governor Control Linkage and Decelerator - Remove
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Three-Point Hitch Control Valve
527 Track-Type Skidder Machine Supplements Bulldozer Control Valve - Assemble
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission and Transfer Gears - Remove
527 Track-Type Skidder Machine Supplements Bulldozer Control Valve - Disassemble
527 Track-Type Skidder Machine Supplements Bulldozer Control Valve - Install
527 Track-Type Skidder Machine Supplements Bulldozer Control Valve - Remove
527 Track-Type Skidder Machine Supplements Implement Pump - Assemble
527 Track-Type Skidder Machine Supplements Implement Pump - Disassemble
527 Track-Type Skidder Machine Supplements Implement Pump - Install
527 Track-Type Skidder Machine Supplements Implement Pump - Remove
793C Off-Highway Truck/Tractor Power Train Lockup Clutch and Synchronizing Valve - Assemble
824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Piston Motor (Fan Drive)
527 Track-Type Skidder Machine Supplements Governor Control Linkage and Decelerator - Assemble
527 Track-Type Skidder Machine Supplements Governor Control Linkage - Adjust
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Wheel Nuts - Tighten
527 Track-Type Skidder Machine Supplements Refrigerant Compressor - Remove and Install
527 Track-Type Skidder Machine Supplements Refrigerant Condenser - Remove and Install
527 Track-Type Skidder Machine Supplements Refrigerant Condenser Fans and Motor - Remove and Install
527 Track-Type Skidder Machine Supplements Refrigerant Evaporator Coil and Heater Core - Remove
527 Track-Type Skidder Machine Supplements Refrigerant Evaporator Coil and Heater Core - Install
527 Track-Type Skidder Machine Supplements Receiver-Dryer - Remove and Install
527 Track-Type Skidder Machine Supplements Sweeps - Remove and Install